FDR252RBB1 Frigidaire Dishwasher - Instructions

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

Unscrewed the screws on the door, opened it. Swapped out the latch. Screwed the door back together - GOOD AS NEW!

I just had to buy a new cap and screw it in.

Simply unscrewed the old. Replaced with the new.

I followed the instructions in the video. It was really easy and took less than 15mins. Very happy with the part.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.

shut off water supply, unhook water line first so i could pull the washer out first. pull washer out and the valve is on the lower left if your facin the washer. easy to get to and very simple to change out.

The repair was relatively easy and I probably saved enough money as to not have to buy another dishwasher. The part alone was $42. A service call and installation would have made it not cost effective to fix.
The control panel is loosened with phillips head screws on the inside of the door. The latch is attached with the "star" shaped screws. I did not own one of these drivers so I had to leave the house to get one. I used pliers to disconncet the clips from their connections as to not pull the wires from the clips.

At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.

I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.

Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.

I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.

This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!

Felipe,
Poughkeepsie, NY

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

Six screws, two torque drive screws and, four wires.
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy

turn water off,remove hoses,remove valve,install valve and hoses,turn water on

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

FIrst I had to turn off the water supply, remove the bad part and cap off the copper water line.
I found the correct part on line and ordered it. When the part came, I uncapped the water line, doped the ends and refit the valve. Turned the water on an voila!. I actually did it! I was pretty proud of myself. It only cost me the price of the part and not a plumbers fees as well.

replacing 2 wheels was a breeze. did not need the screws afterall.