FDR252RBB1 Frigidaire Dishwasher - Instructions

I used both epoxy on the male threads and then pulled out the case and twisted the flat car body flat kind of a nut. Let it sit for 36 hours and now like new.

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

first of all, my name is virginia , I ordered the part for my husband and because of his work schedule I decided to try to fix it myself. It was very easy, about 8 screws and it was out and the new one was in and working. see, girls can do repairs ourselves.

Removed front cover. No instructions so I removed all the screws. Only the bottom 2 need to be removed(1 on each side) then push cover up to unlatch. Remove 2 wires and 6 screws. Replace soap dish unit. reinstall screws and wires. Replace front cover. The hardest part is the front cover.

After i identified where it was leaking i cut the vave off under sink so i could remove part. All it had was 2 screws holding it to the frame and of course the copper line. I then went online to parts select and within 2 days my part arrived,i was planning on being down for at least a week but not with part select!! Thank you all for the great service!

removed 6 screws to take off door cover . Found two star head screws holding door latch removed them . Undid 4 wires attached to the old latch one at a time and attached in same order to new latch. I put the two star headed screws back in. secured door cover and every thing worked great.

Located where the dishwasher was leaking from and by referencing the parts catalog determined that it was the water valve. I ordered the part from Parts select and replaced the part when it arrived. Replacing the part was very easy and I now have a working dishwasher again.

Replacement was simple.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

I measured the length of the gasket, using the old one to measure the length. Cut it to that length and installed it. VERY SIMPLE TO DO! But it didn't stop my leak--turns out there was a small leak in the bottom of the tub that was easily fixed with some silicone. The dishwasher's like new now!

Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

Removed the broken part and disconnected the four wires. Installed new part (two hex head fasteners) attached wires - good to go!
Quick delivery on the part allowed for dishwasher to be down for only a few days after the part was ordered.

My husband had the water shut off to the dishwasher, he unplugged the electrical connection then disconnected the inlet water pipe with an adjustable wrench. Once that was done he disconnected the water inlet valve from the frame of the dishwasher and installed the new one , he then reconnected the inlet water pipe and the electrical connection , once that was done he opened the water valve feeding the dishwasher and checked for leaks which were none. Took him about 15 minutes to do it . Make sure you have the proper tools and a roll of Teflon tape before you start the job.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.