EF42NBSS Dacor Refrigerator - Instructions

Easy, just removed the ice dispenser and the left support for the dispenser so I could get to the bottom screw easier. Three screws held the mold in place. The bottom screw had to be removed completely, but I just loosened the two top screws and lifted the mold out away from the wall and then disconnected the wiring. The end cover snapped of easy with a screw driver. I then removed the three screws holding the motor. then pulled the motor off.(the next square part under the cover. I did this before I realized that I could use a small screw driver and stick it into the holes to remove the mold and not mess with the outer screws. After I removed the mold, I replaced the new mold into position, without putting the white forky looking part back on so I had to take the two screws out and put the part in place before attaching the motor back to the mold. Everything went back together just like a charm. The ice maker is working good, easy job. Gone golfing now.

turned water off to ice maker unpluged fridg while doing repair which was such short time everything was ok removed 3 1/4 hex screws holding ice maker in position while holding ice maker in hand unpluged wiring connection for it removed old ice mold which coating had come off of which was very simple 2 philips screws which are recessed on control unit then gently wiggle assembly apart paying attention to how all the tray parts went together then reinstalling same way as they were remove very simple repair anyone should be able to do

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

My ice maker just stopped filling with water one day and after some troubleshooting, I found that a chunk of ice had built up in the tube between the water supply line and freezer. I took the ice maker out (Don't touch the heating element...it really hurts) and defrosted the ice obstruction by injecting hot water into the tube to melt the ice. I used a new plastic syringe you get with an infant over the counter drug and a bucket to catch the water. I noticed the ice cube mold was peeling and decided to replace the mold. The mold is an easy replacement as long as you remember how you took it apart. My mold had some glue or compound stuck to the side that kept me from getting the mold flush against the motor assembly housing so I had to uncrew and scrape that gunk off and reattached. Other than that, there was nothing to it. Now the ice maker is good for another 8 years.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Removed grille cap,twisted out the old cartidge. Flushed the water system and twisted in the new,

It's very simple and fast to make.

running like a brand new

I/4 turn and pull out old filter. Insert new filter and turn 1/4. Shipping time from partselect was unbelievable, one (1) day. Highly recommend this company !!! This site is a great help to the do-it-your-selfer. Thank you.

Simply turned the original filter counter clockwise, pulled it out and discarded it. Then I inserted the new filter and turned it clockwise. Repair done.

The hardest part was getting the model number. (My vision is not that good.) After I got the number, the rest was cake! In less than a week, I had it ordered,shipped, delivered and installed!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.