DWXR483EB2CC General Electric Dryer - Instructions

After reading a slew of scenarios that sounded exactly like my situation, I decided that the logical thing to do was give it a go myself. Everyone mentioned how simple it was--pop off the cover, remove wires, reconnect wires to new starter, and boom--up and running. A $22 part (that came VERY quickly) vs a min $100 repair person house call--and who knows if they would have taken me down that path we all know too well..."well, it's a complicated problem and will need blah, blah, blah, and $$$. Even my wife was impressed at how I "diagnosed" AND fixed the problem easy, quickly, and for a $22 part! Very pleased (with myself, too)!

1. Unplugged dryer
2. Removed 6 phillips screws from back control panel
3. removed wires one at a time and installed on new switch
4. removed knob
5. lift lock lever and rotate switch ccw
6. installed new switch , rotate cw and be sure lock lever secures switch.
7. install back panel and knob

very simple , unplug dryer and unhook the back of the top of dryer using a screwdriver on 6 screws. unhook clip to the rotary starter switch and unhook the three pronged plugs that go to the starter switch. replace new one that snaps into place, plug back in the three wires. screw the back of the dryer back on and your done. 6 minute job that saves you 40-50+ dollars for a repair man plus the extra money they mark up the parts

Unscrewed screws took off new parts and replaced with new parts and put back together. Works great now! No Noise!

Took top off ,4 screws.Took old timer out and just transferred wires to new one, very easy and worked perfect.Would probally get new knob also if ever done again.

Imagine that!! Move 3000 miles from home to home and after 90 days in storage, we finally get our things. First the washer, then the dryer. Test, no water, okay...Open valves. It's like magic. Hmmm. Plug the dryer in. No sound, not a peep. Turn the start switch one more time, crack-crack, the knob falls in my hand. Ordered the part and got in 2 days. A few star bolts to remove, unplug 3 wires and presto, it works like magic. Thanks!!!

Pulled front panel off, popped off the old switch, popped on the new switch. Good to go.

Pulled power plug. Removed the "Start/Stop knob" Removed 4 starbit screws across the top of the control panel. Flipped control panel down(toward front of dryer)to expose swithes. Aligned the new switch next to the switch being replaced, removed a wire and re-installed on the new switch. I did for each wire. To remove old switch, rotate counter-clockwise and lift out. Line up slots on new switch to panel slots, push down and rotate clockwise to lock in place. Re assemble panel, line up slot on switch knob to switch shaft and press on.

I took off the dryer top and saw it was the slides went on line found PartsSelect, found my dryer, ordered the parts and had them within two days and it took me about 15 minutes to fix the dryer which will add about 3-4 years more life on it. Thank You PartsSelect My wife is even happier

I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!

Pulled the dryer out away from wall. UNPLUG dryer. Using Phillips screwdriver remove the 5 screws holding the metal plate behind the back splash. Remove the 2 screws holding the smaller metal plate at bottom center of the larger . From the front pull the start knob straight out remove. Grasp switch and turn clockwise and pull out switch. Hold new switch and pull wire/ terminal one at a time and install on new switch. Repeat until all wires are installed on new switch. Rotate switch to approximately two o'clock position and while pushing turn switch counter clockwise to lock switch into position. Reinstall all plates that were removed. Plug back in and reinstall knob noting "d" shaped inside dial to line up with shaft.

I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.

Inserted replacement door handle into two slots on door and snapped into place. Amazingly easy and a perfect fit!

replaced the start switch, and it worked like new. took me only about 5 minutes to replace the switch. thanks!

Removed and replaced knob.