DU8700XT0 Whirlpool Dishwasher - Instructions

First, I checked the ripped box for damage to the dishrack. Fortunately, there was none. Then I looked for the instruction booklet. Unfortunately, there was none. And the parts bag was ripped and I did not know what was supposed to be in it. So, I rechecked the photo of the dishrack on the website and found that either parts were missing or the dishrack was different than illistrated. After a few moments of thought, I realized the latter was the case. I then figured I would have to use some deep thought to do the installation since neither the missing instruction booklet nor the unzoomable photo would help. So, I pulled out the tall thin thingamabob from the old dishrack and put it in the new one though it did not secure as tightly. Then I put the wheel units on just like the old one. What I could not immediately figure out was where the collapsible rack row was mounted. I eventually realized that the rod went into a hole in the wheel units and the latch mounted above one unit. I still have no idea where the two other tan clips go. Though the dishrack is different and thus requires different science to fill it, it appears to do the job.

Thanks for asking.

By the way, it was not blue.

I bought the kit because it had other parts that I thought I needed.

It was a piece of cake, just slapped together and slid it into place!

Simply snapped new spray arm in place. Took longer to get the soray arm out of the shipping package.

I simply snapped off the old broken roller set and snapped on the replacements. No tools were even needed and now the rack rolls smoothly on all wheels! This has encouraged me to try other
repair projects.

removed the 2 screws that hold in the washer, pulled it out, with the door shut, removed and replaced the remaining spring , then went to the other side and did the one that broke off. then I reinstalled the unit. simple !

This job took 30 seconds to accomplish. The old wheel assemblies (4) just snapped off and the new wheel rollers just snapped in their place. No tools were needed. Extremely satisfied with this product. Wished I had performed this repair years ago!

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

The lower dish rack rolls directly out of the dishwasher without problem - there is no permanent attachment. The new rack comes as a kit, which includes the 4 required dish rack wheels (Part # 6 in the diagram). One part (only) from the original dish rack needs to be removed and re-installed on the new rack - the upper spray arm tower (Part #5 in the diagram). That is easily removed from the original rack with a 1/8 counterclockwise turn, to disengage the 'feet', and installed on the new rack with a 1/8 clockwise turn. The kit is designed to allow for use on multiple models, so there are 'extra' parts left over, after it is used for the DU8500XX-2 dishwasher. These can be discarded.

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

after that every thing went very well

This repair should have been rated "Easy" but because of a) the age of the dishwasher - 25 years and b) the close quarters to replace the spring, it was a bit of a challenge. If I could have pulled the dishwasher out a few inches, replacing the spring would have been a snap. But because of new flooring on top of existing flooring, that wasn't possible. Also the side cabinets were so close that getting a pair of pliers in there to hook the spring onto the door was tough. Ended up cutting out some cabinet facing that wasn't going to effect the look of things in order to get my hands and tools in there to get the hook end of the spring on the door. After I finally got it on and replaced the kickplate, sat back and had a cold one. Whew!

Replaced Seal and Seal Frame worked real good

Removed the two screws securing the dishwasher to the underside of countertop.
Pulled the washer out until the spring mechanism was visible. Vacuumed the area - it was filthy. Assembled the spring and adjusting hook. Took me 4 tries to get the spring into the proper tension slot. Having the other side intact helped in understanding how it worked. Used long nosed pliers to bring spring onto the door retaing plate slot after trying unsuccessfully with regular pliers.

Pulled out the DW and removed old spring parts. Used screw driver and pliers to respring