All Installation Instructions for General Electric Dryer DBXR463EB0WW

a lot

started with replacing the belt and tension pulley which I purchased from another source. I found your videos on line and they are great. easy to follow. Realized I needed the bottom vent assembly and your prices were better than my local supplier. It was easy to replace thanks to your video. It was nice that you included it in the final order status. The only problems. Did not know the duct felt seal was included with the new duct assembly. I ordered the wrong bearing slides, web site showed both green and white for my model. I now realize I should replace the upper bearing housing. Can I return the unused parts, unopened and have that put as a credit to my next order? Thanks

Parts Used:

Dryer Lint Chute Assembly

Craig from HOPKINS, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Rubbing noise while dryer was running

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Carol from Simpsonville, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Dryer was making a loud squealing noise.

I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Patrick from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Loud squeek when dryer was running

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Clarke from Grapevine, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Timer knob and shaft had stripped

Replaced switch by taking out top 3 screws in back of control panel. Hold new switch in one hand and took out wire(female discount) one by one as they matched old switch. Put back in holding slot, screwed back together, DONE. If I had someone help it wouldn't have taken 10 minutes

Parts Used:

Timer Knob

James from INDIAN SPGS, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The Start knob broke off

At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push

Parts Used:

Knob and Clip

Sally from MANHATTAN, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

On knob went bad

Took new one out of package, and push it on. 4 seconds!

Parts Used:

Knob and Clip

Bruce from ELVASTON, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Bulb was intermittently working

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Parts Used:

Light Bulb

Peter from LEOMINSTER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace a broken timer knob

I just put the piece in place and it fit perfectly. I didn't need a tool for the installation.

Parts Used:

Timer Knob

Maria from MIRAMAR, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer would not turn on

ordered knob ,. pushed it on.

Parts Used:

Timer Knob

Bernice from INDIANAPOLIS, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

timer knob would not work - it just spun around - wouldn't catch

watched video on your site - pulled knob firmly straight off - pulled off small metal piece that remained on plastic dryer knob - pushed on new knob -!!!

Parts Used:

Timer Knob

Judith from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

My dryer wouldn't start, I saw the part on your website after reading comments from other people

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.

Parts Used:

Knob and Clip