DBB3300GA0WW General Electric Dryer - Instructions

The repair was pull old one off and replace new knob. Receiving the new knob was amazing. Ordered one afternoon and received new part by 11 am next morning at regular shipping. You can't ask for anything better than that. Thank you

Silmply replaced the knob. This is the second knob I have replaced on this dryer. This time I bought two for when it happens again. Not sure if it is too much rension in the timer or too little strength in the knob, but is a design problem.

The fact that the knob on a 3yr old dryer broke was harder to deal with than the repair. It was lift the old knob off (it was very loose) and snugly slide the new knob on. I can get back to reading my book and my wife thinks I'm a hero win-win!

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

The repair was extremely easy. Just pulled the broken knob off and replaced with the new one. No tools required.

r/r parts unit runs great

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

I ordered to timer knob. Its was delievered in two days. When I received it, My bother and I looked at it expecting more than what we received, We said to each other this isn't going to work. I told my bother to go on and try it anyway. He took the old timer knob off and then removed a clamp at the base of the timer knob fitting. He then placed the timer knob back of the fitting. Turned the dryer on and it started right up. We were both shocked that it ran and that it was so easy to fix. Thank you PartSelect. Great customer service. I have already ordered a part for his refrigerator! Can't wait till we get the part. I'm sure its going to work just fine.

My husband snapped the new know easily into place.

I was tired of the process after having the know break three times in less than three years which makes me think there is a design flaw.

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

followed instructions that came with kit. The problem was the instructions were not very clear with regard to the "type" of burner. the "A" type with the slot is explained but the "B" without the slot wasen't clearly explained. Even that wasen't too bad (I had to re-do that part), But you need to be 20 years old to see the damned print. I had to use my reading glasses AND a magnifying glass to read them. Also with the "B" type burner, which I have, you simply install the limiter part and you don't need (can't) adjust it.

To get inside the dryer in this model is extreemly difficult. I had to remove the side panel. In order to do this I needed to take off the screws on the back cover side where I needed to replace the cord. Then I needed to remove the screws to take off the top cover, front door, rear panel, trim switch, and end cap. I also had to remove the front door. After that I could tak off the side panel and change the cord.

Checked all thermostats, they were good. Circuit was getting 220 vac. Eventually found fuse in the back near the heating element, same was bad. By-passed same, and when we did, the timer Popped & arched !. Not sure why. Motor protectrion fuse found to be good. Heating elements good. Fuse was the only bad part found, never figured out what caused it to blow. Appliance was taken away after purchase of new one. Problem not found or resolved by self diagnostics. Originally the exhaust duct was somewhat clogged with lint, but not severely.