Models > DBB3300GA0WW > Instructions

DBB3300GA0WW General Electric Dryer - Instructions

All Instructions for the DBB3300GA0WW
31 - 45 of 132
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I had to convert from natural gas to liquid propane
My son is an engineer and repairs washers and dryers for a large commercial laundry company on a daily basis. He installed my part easily and had me up and running in no time.
Parts Used:
Natural Gas to Liquid Propane Conversion Kit
  • Sandra from Brazil, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
Parts Used:
2-Coil Gas Shut-Off Valve Assembly
  • William from Deerfield, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer knob and shaft had stripped
Replaced switch by taking out top 3 screws in back of control panel. Hold new switch in one hand and took out wire(female discount) one by one as they matched old switch. Put back in holding slot, screwed back together, DONE. If I had someone help it wouldn't have taken 10 minutes
Parts Used:
Timer Knob
  • James from INDIAN SPGS, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
On knob went bad
Took new one out of package, and push it on. 4 seconds!
Parts Used:
Knob and Clip
  • Bruce from ELVASTON, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace a broken timer knob
I just put the piece in place and it fit perfectly. I didn't need a tool for the installation.
Parts Used:
Timer Knob
  • Maria from MIRAMAR, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not turn on
ordered knob ,. pushed it on.
Parts Used:
Timer Knob
  • Bernice from INDIANAPOLIS, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
timer knob would not work - it just spun around - wouldn't catch
watched video on your site - pulled knob firmly straight off - pulled off small metal piece that remained on plastic dryer knob - pushed on new knob -!!!
Parts Used:
Timer Knob
  • Judith from CARMEL, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Parts Used:
Door Switch
  • Alan from BELFORD, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Knob broke.
Just put the new knob on.
Parts Used:
Timer Knob
  • Shirley from ASHEBORO, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Parts Used:
Knob and Clip
  • Margaret from SCOTTSDALE, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer knob broke
Just put it on, but this is the second time I've had to replace this knob in 3 yrs.
Parts Used:
Timer Knob
  • Shirley I from Judsonia, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Making noise while drum was turning.
Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.
Parts Used:
DRYER FRONT BEARING WHITE 2PK
  • Cheryl from Inwood, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken timer knob
All I had to do was snap it on and was ready to go. How easy was that. Would order any other parts again.
Parts Used:
Timer Knob
  • Corinne from Woodstock, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked timer knob
It just popped into place :)
Parts Used:
Timer Knob
  • Susan from Palmdale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob to set timer wouldn't advance
Removed old knob, took a pair of needle nose plyers to remove wire band that was left behind from original knob. Slipped on new knob and voila! Easy fix! Now I need to replace rotary start switch.
Parts Used:
Timer Knob
  • Barbara from Goodrich, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DBB3300GA0WW
31 - 45 of 132