CWG3600AAB26 Maytag Wall Oven - Instructions

Replaced gas oven ignitor

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

I was sure my problem was due to a gas ingiter that was no longer working. I read about others that had the same problem as I did. I ordered the part from Partselect because they had a 30 day no hassle parts return policy.
I removed the oven racks and 4 screws to get to the igniter.
I unpluged the igniter, put the new one in, and replaced the racks. Very simple and easy to do.

I removed the cover protecting the igniter. I pulled the stove away from the wall to get at the connect for the igniter. I loosened the 2 screws which held the igniter.
Took the new igniter ran the wire to the back to the connection and mounted the igniter with the 2 screws. Turned on the oven to make sure it works and it did. Turned off the oven, replace the cover and pushed the stove back in place. No big Deal!
Your web site was very helpful. Thank you so much!

After reading how others replaced their defective Gas Oven Igniter, I decided to attempt the project. My only mistake was Removing the Oven Door. Though it came off with ease, it was a complete bear to put back on.
Once I removed the oven door, I located the two phillips head screws that held the bottom oven floor in place. One screw came off without much effort, however the other stripped and had to be drilled out.
After removing the oven floor plate, I quickly located the Igniter and using a nut driver, unscrewed it. One of the two screws stripped on me and had to be replaced. The new part was put in position and the process was reversed. This is where I encounted a problem.
After repeated attempts, I soon found that the oven door hindges had to be held in the open position with a flat head screwdriver in order to be put in place. I found no instructions or info on how to complete this process (even from Maytag) and only completed the tast by trial and error. I highly suggest NOT REMOVING THE OVEN DOOR to complete the repair. The repair itself is rather simple even with stripped screws.

Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Replaced glass door - very easy.

First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!

This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.

Unplugged the oven from electricity. Took off the bottom(Floor) of the inside of the oven. Checked that the new part looked the same as the old. It did. Then I checked the back of the oven, had to take off a cover, and the connector in the back was not the same. I did not that it had the same two wires so rather than send it back, I figured I could make it work. I started to take off the old piece by unscrewing the two screws. They were a bit rusted, one came off the other I had to hacksaw and twist off. I cut the old connecting end off of the old part and the end off of the new part stripped the cover off the ends of the wires, and put the old end to the new part, having also put the old wire covers over the new wires. then twisted the end together and wrapped the in electrical tape. I had to take the piece that held the new part out of the oven the tried to use the one semi-good old screw, then some newer screws, then finally used some new nuts and bolts to connect the part tightly. put everything back together and it worked.

It was really easy. Watched a brief tutorial on the Internet and went to town. Followed the instructions and had a working oven in no time at all.

Bought the igniter, replaced it with the old one and it works great.