CWG3100AAE29 Maytag Wall Oven - Instructions

Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble

Did not have gas smell, but ignition took 6 minutes

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Removed bottom tray in oven, used nut driver to remove igniter, pulled oven out from wall and unplugged cord, did steps in reverse and repair was done. Very good tip on what was wrong with oven and how to diagnose the problem. I will defintly use your tips and purchase parts from you in the future if the need arises.

My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings

very easy

Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.

Make sure the knobs are all in the off position before starting the work. You may feel more comfortable shutting the gas valve off behind the stove or in the basement first, just make sure you fire the burner and let the gas that is left in the line burn off.
Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.

removed 2 screws on element then unpluged it then replaced it with new one easy job

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.