CED9060AW0 Whirlpool Dryer - Instructions

An online help site lead me to believe the problem was the gas igniter. After ordering that and installing it I discovered that wasn't the problem. I took a look at the schematic which is in the electrical compartment and found that there is more than one thermal breaker. I found the other one, ordered and installed the part and had it running within 30 minutes. I had to access the back of the unit, remove the back cover with a socket wrench, unscrew the thermal breaker and re-install the new one with no special tools.

Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.

The repair, replacing the thernal fuse was easy, just one screw and then remove and replace by disconnecting and reconnecting two wires. It did take a bit of time to find which part was defective. I first removed the back panel and front panel and the drum to get at the igniter and flame window. I checked continuity of these parts as well as the gas solenoids and they all checked out ok. The thermal fuse was last on my list. It read as an open circuit. I temporarily jumpered the two wires at the fuse and checked that the igniter would now heat up. I spent over one hour removing the ductwork and giving the unit a thorough cleaning with a shop vac.

Unplugged dryer from electrical outlet. Removed top panel from dryer to get instructions for location of parts. Removed front panel to get to fuse and thermostat. Had to purchase small socket wrench to access nuts because of small space and angle of difficulty. Removed both parts, and replaced with new parts. Plugged dryer back in. Tested for heat. Working properly.

Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding each one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.

First I pulled the dryer away from the wall, after which I disconnected the power and dryer vent. I then removed the eight screws holding on the back of the dryer. Next, I disconnected the two wires to the part and unscrewed the mounting screw. I then removed the bad part, replaced it with the new part, and reversed the above steps.

How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.

I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.

just replaced parys

The Termal Fuse did not solve the problem. Ordered a heating element so I hope its that

Attempt to start dryer normally. Turn timer dial to high heat setting. Press the Push To Start button. Verify plug is secure in wall outlet. Got to breaker panel to verify breaker is not tripped. (Sometimes breaker may trip but visually appear no to be tripped). Reset breaker to maker sure breaker is in the on position. Attempt to start dryer normally. If dryer did not start proceed. Get a multimeter. Remove plug from wall outlet. Slide dryer from wall. Remove exhaust duct from bottom of dyer. Use multimeter to check voltage at wall outlet. Verify 120 to ground and 208 between hot legs. Remove rear cover if main dryer unit and rear of control unit. Connect the multimeter to rear of control panel rear of push button. Turn meter to ohm setting. Push the start button to see if there is continuity. Release the button to verify no continuity. Next major part of curcuit is the thermal fuse. Look on lower left area of dryer. With multimeter in Ohm mode place the leads on the light blue wires. If no continuity replace thermal fuse

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

Dryer works - thanks to a new fuse. Glad I tried this before just buying a new one. Video for my model indicated the fuse was located in the back and actually it was difficult to get to in the front. So extra time was wasted trying to get to fuse in the back. Thank you for the part!

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I made sure air vent was clear and clean. I removed front panel of dryer unit, located fuse, removed wires, tested fuse with ohm meter, which was defective. Tested new fuse placed back in dryer reattached wires. Cleaned out inside of dryer, replaced front panel. Now works like new.