CED9060AW0 Whirlpool Dryer - Instructions

removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

Removed the old screen and simply put in the new one

With the instructional video the repair was very easy.

Replaced Thermal fuse, hardest part was getting behind the drier to disconnect the gas & vent line.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Replaced all 4 sensors. Still no display. Ran my thumb across all control buttons several times. Machine showed life. Looking good, but low heat. Replaced the heating coil, and now we have a new, 13 year old machine.

Followed the Video on how to replace,

I remove the back panel then look for thermal fuse.. so easy to replace.. thank you so much ..

An online help site lead me to believe the problem was the gas igniter. After ordering that and installing it I discovered that wasn't the problem. I took a look at the schematic which is in the electrical compartment and found that there is more than one thermal breaker. I found the other one, ordered and installed the part and had it running within 30 minutes. I had to access the back of the unit, remove the back cover with a socket wrench, unscrew the thermal breaker and re-install the new one with no special tools.

Had to call service company to come and do the repair and they had the correct parts. PARTSELECT is a very terrible company to do business with. They sent incorrect parts and will not answer the phone or respond to emails after two weeks. will report to BBB.

Unplugged dryer from electrical outlet. Removed top panel from dryer to get instructions for location of parts. Removed front panel to get to fuse and thermostat. Had to purchase small socket wrench to access nuts because of small space and angle of difficulty. Removed both parts, and replaced with new parts. Plugged dryer back in. Tested for heat. Working properly.