CDT706P2M4S1 General Electric Dishwasher - Instructions

I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

Followed instructions sent with wash arm kit replacement. Very easy.

Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!

Just snap part in position quick to do.

When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Pulled washer out of space to access cables to the door. Removed moved the cables by stretching springs and unhooking cable from door. Disconnected wire from door to machine in body of machine. Opened door an lifed on an angle that allowed door to be lifted out of hinges. Unscrew and remove hinges on both sides. Remove by simply pulling them straight in direction of the bottom of the door. Then unscrew bolts on either side that are now exposed after taking hinges out. Then push inside of door up and remove. Unscrew the control board unit. Un plug cable to control board. Remove bezel cover. Then carefully unsnap unit case and remove board. Replace with the new board. However since this is a replacement part it must be configured for your machine. Instructions shou you the configuration. However where I ran into a problem was dining out how to set it. There were no switches. What I learned was that altouch it looked like one piece the jumper connections actually were four separate pieces that were tightly fitted together. In order to get the configuration you simply have to lift the jumper connector up. Once done reverse process and your done. If I did not run into that one issue repair time should be 30 minutes tops.

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.

Bought replacement rack transferred all the accessories from the old to the new. Mostly snap-in-place.

The repair was just like the video that the agent sent me. And while I had the unit out of the cabinet I installed a part I have had for months which I ordered before I realized I had to take the unit out of the cabinet: the part was the seal for the bottom of the door. I recommend if you are ordering a pump order this part too an it is easy to install if you already have the dishwasher out of the cabinet.

Replaced old One,Watched a Clap on You Tub !!!

We I installed a new dishwasher pump. It was simple and easy. I did it myself. My husband removed the clamps holding the dishwasher in the cabinet. Then he turned it in it's side and I replaced the old pump for an identical one that I ordered from this site. Easy peasy, took all of 15 minutes. You've got this. Don't call a repair man and pay $300 or buy a new dishwasher and pay $800. This repair was $63. If I can do it, you can!!!