CDT706P2M4S1 General Electric Dishwasher - Instructions

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

- Removed standing water using shopvac
- Uninstalled dishwasher
- Hooked up hoses temporarily and ran dishwasher
- Cancelled wash cycle and started drain cycle - checked drain pump voltage at pump power cable - OK
- Measured drain pump windings and verified open circuit
- Ordered new drain pump
- Removed old drain pump and installed new unit
- Hooked up hoses temporarily and ran dishwasher - OK
- Re-installed dishwasher

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Replaced latch

Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Downloaded the GE manual from the internet. Followed the GE repair manual trouble shooting guide. The manual contains all of the disassembly and reassembly instructions. Main board had a more than one volt higher than listed voltage output. Manual does not list an acceptable voltage range so I ordered a new main board. New board had the same output and did not fix the problem. I ordered a new UI board. The new board is a genuine GE "programable" replacement board that covers multiple models.
I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference.

I watched a YouTube video that showed how to to do this. The first trick is finding the right video. This one worked best for me / my model.

https://www.youtube.com/watch?v=sesf0BS8fzM

The first few I watched were for models with the user display on the top of the door, and you have to open the dishwasher to see it. Mine shows the display on the outside. Look for the video that has a round plastic "vent" on the inside of the door. You will have to loosen it with some sort of tool in order to remove the display once you get the door taken apart. In the video, they used needle-nose pliers opened wide. My NN pliers don't open that wide, so I used two screw drivers. Pealing off the display is a bit challenging. I was afraid I was going to break the little plastic pins that hold it on. The rest is not too hard though, and it went back together quite easily, even though I did break a plastic piece that 0ne of the UI Control Board screws goes into. Oh well, now it has three screws holding it instead of four.

Pretty easy repair, since I installed the DW, so knew how it went in,
turn off breaker, shut off & disconnect water, disconnect drain line into disposal, siphoned water out of bottom collection basin below sump filter.
Slid DW out from under counter & laid on it's side.

Glad I watched a YouTube video so I knew to pry open 1 of 2 crimp style hose clamps on the old drain pump, then made sense why this was a drain pump "kit" that included 4 or 5 standard band hose clamps.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.