All Installation Instructions for Maytag Range CDE8300ADB

replaced the current warn-out grease filter

removed the old by pulling it out of track and replaced it with the new filter

Parts Used:

Grease Filter

Joseph from East Greenwich, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

worn door seal on oven

takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place

Parts Used:

Oven Door Seal

Sarah from Albany, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

front burner stayed on high

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

Parts Used:

Surface Burner Switch - 240V

Natalie from North Reading, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

needed new grease filter

It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)

Parts Used:

Grease Filter

Barbara from Hubert, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Filter Worn Out

Remove cover and install

Parts Used:

Grease Filter

Thomas from Berlin, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

could not adj. temp. stayed high all the time

replaced stove top switch

Parts Used:

Surface Burner Switch - 240V

Don from CARROLLTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

grill was getting red hot with out control

Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions

Parts Used:

Surface Burner Switch - 240V

gilbert from san antonio, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

replaced oven lightbulb

very easy

Parts Used:

Light Bulb - 40W

peggy ann from forest city, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

back burn would turn high no mater where you set the control knob.

Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.

Parts Used:

Surface Burner Switch - 240V

William from Valley Grande, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

Light Bulb - 40W

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 10 people found this instruction helpful.

Was this instruction helpful to you?

worn out / burned grill and components

very easy - not really a "repair" more of a face lift, although the grill was unusable.

Parts were perfect - Used it the same night.

Parts Used:

Rock Plate

Single Grill Grate - Black

Rock Grate Support

Brian from Lafayette, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

light bulb went out in my oven

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Parts Used:

Light Bulb - 40W

Janet from Ada, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

bad surface burner switch

1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.

Parts Used:

Surface Burner Switch - 240V

Lawrence from Birmingham, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

one of the four burners was not working

Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!

Parts Used:

Surface Burner Switch - 240V