All Installation Instructions for Maytag Range CDE8300ADB

worn out burner switch

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Parts Used:

Surface Burner Switch - 240V

William from ARCADIA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven switch not working

Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven

Parts Used:

Light Bulb Socket

Light Switch

Terry from DIAMOND BAR, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Range oven door switch need replaced

I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294

Parts Used:

Light Switch

Ruth from Gastonia, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.

dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.

Parts Used:

Range Burner Cartridge Terminal Block

Cartridge Male Contact Spade

Ge from Solon, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Needed replacement oven rack.

Part was perfect fit. Good product, good value, great service.

Parts Used:

Oven Rack

Bobby K. from Huntsville, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

replaced grease filter

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

Parts Used:

Grease Filter

Light Bulb - 40W

Gregory from CARMEL, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

filter was deteriorated from 15 plus years of use

lifted the top center panel off removed old filter installed new easy peesy

Parts Used:

Grease Filter

Steve from Marshall, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Grease filter clogged and in need of replacement

EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.

Parts Used:

Grease Filter

Mark from STAUNTON, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Old one was plugged

Pulled out old one and slipped in the new one.

Parts Used:

Grease Filter

Rudy from GARIBALDI, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

switch went out

removed the two screws that hold the switch unit into the housing that sits on top of stove. Noticing the electrical connections, I secured the power to the oven by shutting off the circuit breaker. I then removed the faulty switch from + and - wire connections and cleaned and reconnected wires to the new switch and slid new unit back into upper housing and put the screws back in to hold it in place. I turned the power back on, toggled the switch, and heard the ventilation fan whirl. Piece a cake. So gald I was able to find the part. Teddy Schoewe, Winona, Mn.

Parts Used: