BX521VCPER (P1325030W B) Amana Refrigerator - Instructions

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Had to disassemble ice maker to install part. . .

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

simpley place the support into slot provided.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Easy but time consuming. I followed the excellent video instructions on this site and read through all the user comments before starting. I am a handy 65 year old woman who did this alone. I put the gasket in the dryer for 15 minutes then laid it flat for 24 hours before starting. I used a kitchen spatula to release the failed gasket and the plastic panel from the freezer door. The old freezer gasket allowed moisture into the insulation behind the plastic panel on the inside of the freezer door. The insulation inside was frozen solid and took several hours to defrost before I could continue, so prepare for down time by unloading your freezer. I used spray foam insulation after removing the old insulation and cleaning the plastic panel. The foam expands 2x so don't overfill the crevices or you will have to carve it out later like I did. It's really messy so wear gloves and protect surfaces. Putting it back together is easy. I used a heat gun to smooth out the kinks in the gasket and used the spatula to slide the gasket in place. I learned the hard way that there are 4 oval shaped openings on the plastic panel (one on each side) that should be screwed in first to align the panel correctly before screwing in the rest of the screws. My 25+ old fridge is running like new again! It's quieter and the blower isn't running as often. Very happy.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I removed the screws holding the side onto the drawer, removed the side, placed the new one on and put the screws back.

Very easy to order from parts select. Took seconds to replace.