BX521VCPER (P1325030W B) Amana Refrigerator - Instructions

I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Removed two screws that held cover plate. remove cover plate. Remove water hose, and clamp, by compressing clamp with pliers. Remove fill tube by pulling HARD, from back.

Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

After the backordered gasket arrived, I took it out of the box and placed it over the back of a kitchen chair and used the hair dryer to get the shipping kinks out of the gasket. After unloading the door of the Freezer compartment, I made a temporary door from a piece of styrofoam board. After removing all of the screws holding the gasket and inner panel to the door, I removed the inner panel and took it outside to melt the ice acumulated on the back and to install the new gasket. I removed the old gasket, and installed the new one over the edges of the panel carefully to avoid tearing the gasket and make sure it was evenly laid out on the panel. This installation went easily because I took the time to see how the old gasket was on the door before I removed it.
I then scewed the panel with the new gasket to the door of the freezer. Once back on the refridgerator, I used the hair dryer and a dull putty knife to get the edge of the gasket pressing firmly against the refridgerator frame. This last step was critical, because the gasket was distorted by the packing and storage of the gasket in the shipping box. I was not satisfied with the amount of magnetic pull from the new gasket and used Vasaline Jelly to create a better seal with the refridgerator.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to remove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

very easy.....
1. removed the food items from the shelf
2. raised the shelf and removed the broken support post
3. inserted the new support post and guided the drawer rails to rest in the new support slots
4. cleaned the glass shelf and replaced the food items
5. made my wife very happy now that the veg drawer opens and closed like new.

The ordering was easy, however the installing was very difficult. Screws all around door had to not only be loosened but most had to be removed in order to get gasket behind the lip. We (my 17 yr old daughter and I )unscrewed the top and half way down the the sides and did half and half. The job took us approx 4 hrs. In all fairness neither one of us has every done anything like this and we were very proud of ourselves for accomplishing the task. When the gasket was in place we used the blow drying to smooth the gasket. Probably not anything I would attempt again because of the time committment, however, I was trying to save some money.

Someone suggested removing the door, however, I couldn't figure out how to do that. On the up side, it did give me the confidence to replace a screen door myself. You tube helped me with that. ( I couldn't find a "how to" on how to install this gasket at least not for this type of appliance.

Last night, I replaced the gasket of the bottom freezer drawer on my Amana refrigerator. It took me about 2 hours.

When I took my new gasket out of the package that it was mailed in, it had been folded and was all twisted. There were wrinkles in the area where the actual magnetic seal occurs. I tried to use a hair dryer to smooth out the wrinkles but the hair dryer just wasn't getting hot enough. I decided to install the gasket anyway hoping that the wrinkles would just get stretched out.

First I had to remove the drawer which is explained in the Amana manual. I had to remove two screws on the side the the drawer slides and then lift out the hanger for the door. Pulling out the old gasket was really easy but when I tried to push the new gasket it just wouldn't go in under the lip and I was afraid that it would get torn if I pushed it in with a screwdriver.

So I had to remove all 20 or so screws that hold the white plastic retaining liner in and hold the lip of the gasket. Then I had to slide a flat head screw driver in to lift up the liner and break the gluing effect of the expanding foam insulation used during manufacturing. Once I could freely lift up the liner about 1/4 inch, I was able to push the new liner in. The wrinkles were still there, which would have prevented a good seal. Fortunately I had a heat gun which I tested first on the old gasket. This worked wonderfully after the gasket was fully installed and did not melt the white plastic liner.

Once the gasket was installed and all 20 screws were tightened, I discovered that the door had been twisted a little and the left side of the drawer would hit first leaving a gap on the right side. By pushing on the right side some time it would stay but often it wouldn't. So I loosened the screws that hold the door on to the metal hangers that attached to the glides and then twisted the door while I tightened those screws.

The final fix was to tighten the leveling screws so that the top of the fridge leans back. This is recommended in Amana's instructions but had not been done for our fridge. This causes gravity to pull the drawer closed.

I don't mean to scare anyone away from doing this repair but it ended up being harder than I thought.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

First unload the doors, and remove each door from the fridge and freezer. I placed the doors on the counter island and removed all the screws from around the perimiter with the battery drill. Lots of screws. The freezer door had some Ice accumulated in the insulation inside the door. I salvaged as much of the dry fiberglass and tossed the wet stuff. I cut some strips of fiberglass from a roll of 3.5" I had to replace the tossed insulation. The door seal installation went smoothly and the door rehanging was easy also.