AZ2727GIHB Maytag Refrigerator - Instructions

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

disassemble the front panel removed two screws and panel fell forward took old part out cliped in new one and reassembled very easy job

removed three nuts from the top of the door diconected the electrical connections for the ice and water in the door. Removed door by lifting it up about 2 inches, set it aside put new hinge pieces in placed put everything back together. writing this took more time. wanted to add, bought at 2 pm on thursday was at my house by 10am the next day

I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!

At first I thought I had ordered the wrong bracket but all I had to do was push it up and pull down and it snapped right in place. If a 71 year old lady can do this any body can do it. Thank you for the fast service.

First I removed the two screws to remove outside cover. Then removed three screws to the ice dispenser assembly. Slipped in the new round door assembly and replaced the removed screws. No problems.

It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims).
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new

The biggest problem I had was finding how to remove the old broken support. I did a google search and found the answer on your web page, grab it with pliers and rotate it 90 degrease then pull straight out. Installing the new one was even easier just do the reverse.

Thought this repair would be easy, but it turned out to be a bit difficult. I started removing the gasket screws with a 1/4" nutdriver from the top to about halfway down the sides. I soaked the new gasket in hot water for about 15 minutes to make it "pliable" and get rid of the "wrinkling". It did not work. I had a heat gun for backup to smooth out the wrinkles. Only worked slightly better. Things are going smoothly until I run in to a little plastic clip by the door handle. It holds the gasket in place while you place two screws on the short run. It was very hard to remove this plastic pin. I ended up having to loosen the top screws so that I could get leverage to remove the pin and put it in the new gasket. Added a half hour to the job. Worked the rest of the gasket on the door. I continued down the sides and to the bottom. It left me with a lot of play so I loosen the sides again and started from the bottom back up to the sides. It is best to start at the bottom and work back up the sides. Having finished, I am hoping for a tight seal. It has some wrinkles that I hope will work themselves out. If not, I may have to use the heat gun again. Make sure you work slowly and have plenty of patience.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

first I remove screws arounf ice/water door dispenser and pulled dispenser away from refrig door to expose ice door assembly. i removed assembly and replaced and put back together. First time I ever did anything like this was pretty easy saved me some $$$$$$$$$$$$$

Remove (slide forward) the ice dispenser drain pad from the bottom of the ice dispenser assembly on front of the freezer door. Removing two screws (star head) at the bottom allows the ice dispenser cover to be removed. Remove 3 screws holding the ice dispenser assembly to the freezer door to gain access to the flapper. Remove and replace the flapper and reverse the steps to reassmble.

Went very quickly. The biggest problem was manipulating all the frozen packages such that I could reach mounting screws. In the future, I'd be prepared with a cooler to place the frozen goods during the repair time, which required the freezer door be wide open throughout the repair.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

Remove bolt on lower left side that locates the Ice Enclosure. Partially remove Ice Enclosure. Locate electrical connector behind Ice Enclosure. Squeeze locking tabs and wiggle connector free. Completely remove Ice Enclosure and place on work surface. Remove phillips head screws that attach motor to Ice Enclosure. Remove phillips head screws that attach solenoid to Ice Enclosure. Grasp motor shaft with pliers to hold it still. Wedge screw driver handle into motor yoke to gain additional leverage as you turn yoke clockwise (reverse thread) to remove yoke from motor shaft. Keep track of spacer bushing that will fall from motor shaft when yoke is removed. Attach motor and solenoid to new Ice Enclosure. Replace bushing and yoke onto motor shaft. Reassemble Ice Enclosure into freezer compartment. Don't forget to plug harness back in and to replace locating bolt on left side of Ice Enclosure.