ADW1100N35BB General Electric Dishwasher - Instructions

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

There's a video on youtube from this site on how to install spray arm and base. Great video. Great price

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Removed the old one from its slot and slid the new one into it.
No instructions needed.

The lower dishrack just lifted out and the new one placed in. The upper rack had stops at the end of the slides which could be removed with the help of a flat blade screw driver, old rack slipped out, new rack slipped in and the stops replaced on the end of the slide which keeps that upper rack from coming al the way out of the dishwasher. There was a link to a "how to do video" on the email order confirmation. It just gave me reassurance that I could easily do the job.

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.

I removed the warped roller wheel and clipped the new one in place. Then I screwed the rail guides back on the dishwasher and guided the upper rack back onto the rail guides. Easy peasy.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.