All Installation Instructions for General Electric Dishwasher ADW1100N35BB

dishwasher did not start

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Parts Used:

Interlock Switch

Lawrence from ROLESVILLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken plastic spray arm

There's a video on youtube from this site on how to install spray arm and base. Great video. Great price

Parts Used:

Lower Spray Arm

TRAVIS from Webster, MA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water leak under Unit

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

Parts Used:

Water Inlet Valve

GEORGE from LEVITTOWN, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

8 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rinse Agent Tank Leaks

The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.

Parts Used:

TANK RINSE AID Assembly

SCR 8-18 B POR 1/4 Stainless Steel

Paul from Lithia, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wheel had melted and support cracked

Removed the lower rack and installed new wheels with clips

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Tom from UPPR CHICHSTR, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Three of the 8 wheels broke.

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Asok from HELOTES, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

rack slide end cap missing

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Parts Used:

RACK SLIDE END CAP

Carrell from Cochranville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

New dishwasher came with a warped roller wheel (upper rack)

I removed the warped roller wheel and clipped the new one in place. Then I screwed the rail guides back on the dishwasher and guided the upper rack back onto the rail guides. Easy peasy.

Parts Used:

DISHWASHER UPPER RACK KIT 4 PACK

Corinne from San Diego, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Disrack was getting rusty

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

Parts Used:

LOWER RACK

Nelson from Oroville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Upper rack kept dropping from the wheels when we pulled it out

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Parts Used:

RACK SLIDE END CAP

Joel from Cypress, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dispenser cap would not stay in place because it had melted

First I opened the package and screwed the new dispenser cap into place.

Parts Used:

Rinse Aid Fill Cap

Patricia from Clifton, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

detergent shaft and arm broken

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

Parts Used: