Models > ACR4303MFB4 > Instructions

ACR4303MFB4 Maytag Range - Instructions

All Instructions for the ACR4303MFB4
121 - 135 of 148
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old drip bowls, tried prepackaged from box stores
After putting up with ill fitting generic versions of our drip bowls, we smartend up and ordered correct parts. They went in super easy, perfect fit and the heating element is now perfectly level. Who knew that following the manufactors recommendations to buy correct parts would make such a difference? Well we know now! Thank you. The parts were shipped almost immediately and delivered as promised.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Christine from Phoenix, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drip pans missing
placed element in drip pan and plugged in. .Fit perfectly.I am very pleased with the product and service.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Michele from Walnut, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burner control failure/unable to regulate temp.
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Parts Used:
Surface Burner Element Switch, Large Burner
  • ROBERT from SALCHA, AK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip Bowl beyond cleaning
Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Ann from Memphis, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
could not control temp on burner
Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!
Parts Used:
Surface Burner Element Switch, Large Burner
  • Ernie from Cameron, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Old receptacle was burnt from lots of use.
Just cut the old receptacle wires and splice in new kit. Very simple and worked perfectly.
Parts Used:
Receptacle Kit
  • Brenda from Scurry, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken burner switch
Easy as pie! Thank you for the illustration to help us pick out the correct part.
Parts Used:
Infinite Switch - 6 Inch
  • Coral from Duluth, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip plans needed replacement
Removed old ones replaced with new oned
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Margaret from Vero Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replacement drip pans didn't fit -- wrong type
Purchased appropriate drip pans here. They arrived overnight, much to our surprise! The range elements were easy to remove, and the drip pans fit precisely as they were designed to do. Ta Da! repair completed.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Rev Connie from Mattawan, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The original trim rusted
I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.
Parts Used:
Trim, Lower (White)
  • Diane from Elyria, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner would go red after a few mintes
put it off a week before i worked on it but if you can replace a plug on a excord you can do this less than 5 mins
Parts Used:
Surface Burner Element Switch, Large Burner
  • richard from pottsville, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The burner didn't work because it had the wrong drip bowl
Replaced the drip bowls, very simple. Excellent delivery time, ordered them Saturday, delivered Tues morning.
Parts Used:
Drip Bowl - 8 Inch
  • Leslie from Spring HIll, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken oven door handle due to pulling oven by handle.
Warning: Door falls apart after removing the two screws which attach the handle. No big deal, just a suprise!
Parts Used:
Door Handle - Black
  • Dennis from Colchester, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The large burner sometimes stayed on high too long, burning food
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Parts Used:
Surface Burner Element Switch, Large Burner
  • Harry from Seminole, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bowls had burnt on food
replaced them
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • David from Saranac Lake, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ACR4303MFB4
121 - 135 of 148
Back to Top