8KP2670-3 Whirlpool Mixer - Instructions

took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.

The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.

Dear Customer Service,

I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!

A Happy Customer!

it just screw in.

Simply placed it in the slot and pounded until firmly in with a soft mallet. Thanks to your site I was able to find the piece easily and very inexpensively. Thank you so much. I would die if I couldn't fix this machine.

I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.

Took top apart and installed new housing and two gears. Reassembled

Removed plastic cover, removed grease and put in new mixer and put new cover back on.

Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.

Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael

disassembled unit gear head and replaced broken part, then reassembled

Noticed worm gear was worn out, ordered the parts, it came very next day. On YouTube instructions were very easy to follow. Important point to remember,I washed the parts in water with chlorine in it. Retaking ring was tough to take out, as I did not have parrot beak plier, could not find it at Home Depot or Lows. Putting the retaining ring I used circular nut driver, to press it on the shaft to slide down by hammering it. While assembling follow the instruction step by step from the you tube. Machine works smoothly. Performing well. Thanks to part select, excellent web page, efficient delivery. I would recommend them to all.

The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!

This is a 6 Qt. made by Kitchen Aid Stand Up mixer 575. watts with 6 qt. bowl. A powerful machine. But not geared to crush Almonds. After about 2 quarts of Almond crushing to make Almond butter I heard the machine thumbing inside and turned it off immediately. Mind you, I am a 60 year old man with Maintenance Mechanic, and Machinist skills. If you listen to my instructions which aren't that hard you can do this. REMOVE THE POWER CHORD BEFORE CONTINUING. First you have to find the screws that hold the top half of the machine together. They are under the silver Kitchen Aid Stainless Steel 5/8th Band that runs around the middle of the machine. On the back of the machine is a small machine screw that when taken out removes the band. Remove the band carefully as not to bend it because it has to go back on looking pretty. Comes off easy. You will then see 4 longer 3/4 inch screws around the middle of the machine head. When you remove these screws the top half of the machine head will lift up. The top half of the machine head lifts off very easy. Throw all your screws into the top so you don't mis place them. You will see a Motor some gears on the side and a shaft that comes from the motor going into a Cast Aluminum Casing with another 4 screws 3/4 exactly the same size as the ones you took from around the top mixer casing. This is easy cause you don't have allot of different size screws only the one small one that screws on the back of the band. After these four screws are removed, again lift up the top half of the casing but this time it will be full with gear grease. Put the casing aside and using paper towels wife a little of the gear grease off the top gear. In order to turn the gear you must use the side drive gear or look around the gear you will notice in some of the gear slots will be shinny and worn. This is the Bevel Gear. There is a C locking shaft cliff that keeps the gear locked in. You must have a multiple C clip remover pliers that has different size C clips for the holes in the clip must be spread apart in order to remove the clip all the way up the shaft. NOTE:; DO NOT USE A PLYERS TO TRY AND PRY THIS CLIP OFF IT IS STRANG AND YOU MAY MAR THE STAINLESS STEEL GEAR SHAFT. You must use the gear C clip remover, I found one moderately prized for 25 dollars at the Home Depot or any large chain hard ware stores will have it. After the C clip is removed, slide the gear evenly up. If it's stuck that's only because of grease unless you mar the shaft by not listening to me. I also replace the Top Hum Bevel gear which is in the top half of the hub. Parts select has a Diagram that shows you the parts and where they are. When putting on the Bevel Gear over the shaft be sure to lower it evenly and guide it onto the worm gear. There is a small pin that sticks out in the middle of the gear make sure this lines up when setting the gear into the worm gear. The Top Bevel Gear, falls right out and you can use your figures to pull this one out and put the new one in. If you replace the Bevel gear my experience as a mechanics is to always replaces the adjacent gear as well, both will be worn. attach the C cliff the same what as taking it off except opposite. Pull the tow clip holes apart and slide it down to the shaft groove for the clip. Put everything back the way you took it off. One NOTE;.. DO NOT DO TOUGHT THE SIDE DRIVE GEAR IT IS SET IN WITH BRASE LOCKING SHIMS AND HAVE TO BE SET A CERTAIN WAY TO CLOSE. When closing make sure the Top Hub is in line with these brace shims. After screwing the hub back down do not over tighten, just snug it tight. Be sure to buy axle gear grade and replace any grease removed, this chamber must be loaded with grease. There is never too much only too little as you will wear the gears down without the proper amount. DO NOT TOUCH ANY THING THAT DOES NEED TO BE TOUCHED LIKE THE MOTOR OR DRIVE SHAFTS OR SIDE MAIN GEAR…

The transmission housing was cracked and one of the bearings was broken. I replaced both of them, but the mixer really didn't sound any better. So I replaced the gears in the transmission, and while that was better it still wasn't correct. I am going to replace the other bearing and the planetary shaft and see it that aligns everything a bit better. I believe the problem is the way the gear on the end of the motor shaft is working with the worm gear, the bearings are not keeping the correct spacing. Hopefully, the new one in the rear will fix the problem.