7MMHW7000BG0 Maytag Washer - Instructions

Watched a video on the internet.

Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.

Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.

The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.

Once the hose was out I found some bra under wires which is what probably punctured the hose.

Removed the front filter and found a bunch of nails.

Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Went on u tube saw different video to How disassemble the top to have access to the rod. Changing one by one those rod I was in need of my wife to hold the cover while I was changing the rod.... order for suspension rod kit. Reassemble the top by sliding the cover and to snap. Screw back the panel. And it solve the problem. My wife was really happy so me. It can be done by anybody but first go on the internet to get a idea.

First some background. The door locked up the first time when appliance was less than one year old. The "Maytag Repairman" finally succeeded in getting the door open after propping up the front of the machine and fumbling around underneath for a period of time and then assured me the problem was solved. The problem recurred less than a year later, and I called another repairman who seemed to have an easier time of it, and charged $293.42 to replace the water level switch. About six months later the same problem recurred and I took the cover off the top of the machine and found there a booklet "For Service Technician's Use Only". VERY HELPFUL. Told how extremely easy it was to unlock door - took about five seconds. Replacing the switch itself involved pulling one tubing off and disconnecting one elec connection from old switch and replacing on new switch. Total cost $50 plus a few dollars for shipping.

I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

looked repair on you tube followed instructions. took off broken latch. compared to pictures on sites. ordered part. part arrived in 2 days. put part on. suggest using first method quick and easy.

watch utube instruction.easy repair

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.

Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.

Per instruction sent with purchase

Remove top of washer suspension
Rod goes on side of tub .

Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.

Removed the old hoses and screwed on the new hoses.