All Installation Instructions for Kenmore Range 79094153310

Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

Parts Used:

Temperature Sensor

James from S CHESTERFLD, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Crack in inner door glass

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

Parts Used:

GLASS

Robert from Richmond, IN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Change on e of the inside glass

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Parts Used:

GLASS

Ronald from Ozone Park, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Burner switch work sometime.

I follow the video on your site

Parts Used:

Infinite Burner Switch - Small Element - 240V

junius from WICOMICO, VA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

Parts Used:

Infinite Burner Switch - Small Element - 240V

Nelson from FRUITHURST, AL
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not heat or sometimes hold heat to set temp

I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.

Many thanks to PartSelect for their comprehensive website and fine service.

Parts Used:

Temperature Sensor

TRACY from NEW PHILA, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

NO HEAT IN UPPER ELEMENT

NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!

Parts Used:

Broil Element

Jerome from WOOD LAKE, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

run away temp

I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.

Parts Used:

Temperature Sensor

James from ELKHORN, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Two burners did not heat

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

Parts Used:

Terminal Block Kit

Conan from Moline, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

the burner stop working

Just followed the instructions

Parts Used:

Terminal Block Kit

Anthony J from HAMMONTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Original terminal degraded and faulty

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Parts Used:

Terminal Block Kit

Robert from PRAIRIEVILLE, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broiler element fried, found nothing in town, Part Select delivered in three days

Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.

Parts Used:

Broil Element

Gary from TULSA, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stove was dropped and had broken, bent frame and adjuster feet

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Parts Used:

Leveling Leg Assembly

Paul from PORT ORANGE, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Range displayed error code F10

Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.

Parts Used:

Temperature Sensor