79046353401 Kenmore Wall Oven - Instructions

Pulled out stove, took side panel off on switch side of oven, unplugged old switch, pulled the old switch out the front of the oven, put in new switch and plugged it in. Then put oven back together and pushed it back into space. (Make sure to turn oven off at breaker box before you make repair) you could easily get shocked if you don’t.

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Turned off breaker to range then removed all element control knobs. Unscrewed retaining collars I suppose is a good word removed panel. Then removed bad switch installed removed one wire at a time and placed on new switch in proper places. Reassembled in reverse order turned breaker back on worked perfect.

Drawings on web site somewhat hard to read, resulting in more
disassembly than actually necessary. Turns out, simply removing the
threaded plastic securing rings around the bases of the controls frees
up the faceplate, and allows access to the phillips screws that hold down
the bracket. Then it's a simple matter to replace the control unit by
swapping out the leads one at a time from old to new. Be careful when
re-attaching those plastic securing rings, they can cross-thread pretty
easily.

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

First you must disconnect power by throwing the circuit breaker off.You need to pull knobs from cook top. check underside to see if it is mounted to counter top, mine was not. Then raise the cook top and support bottom with 2x2's. Mine had three main screws in front, one on the sides and two in the back. The other thing you need to do is loosen the metal plates that have two screws on each plate. Three plates in front, two on each side and three in back. Once these are loosen, you can lift the stove top up to reveal the indicator lights. I found it was easier to support the top with a pan or something while working on it. Replace your indicator light and put everything back together.. It really wasn't to bad.

I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!