7761A-71 Norge Dryer - Instructions

I did a quick research online and found PartSelect to have the best price. I ordered my part on Monday 8/6 and to my tremendous surprise FedEx delivered it Tuesday 8/7!! I did not pay for overnight delivery. My son happened to come by that day and he took a small flathead screwdriver, pried the old one out and inserted the new part. Done in 5 minutes! PartSelect will be my supplier from now on.

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

order knew door seal fix was a snap just Snap in place

Identified the rollers as the root cause of the drum not freely rotating. They also squeaked a little at the beginning of any cycle. I replaced the rear rollers and shafts using the parts from the roller replacement kit. Easy to do. The hardest parts was re-installing the belt.

took the dryer apart noticed it needed a belt and rear drum supports. Ordered the parts(they were very helpful on getting the right part . they came in very fast (less than 24 hours). replace the broken parts. The dryer is working great.

ordered a new fan from your web site and replaced it. it only took a couple of days to get the part thanks for such good service well pleased will use you again in the future

Removed the front of the dryer removed the casing from the front of the blower and put the new fan in. And now it works great Thank you

I would like to say first of all that I was amaized and pleased at how simple the ordering of this part was and while looking at the parts diagram on you website I noticed the door swing was optional and could be easily changed and the dryer came from the factory with a latch installed on both sides of the door. In our laundry room the dryer sits to the left of the washer and the door to the dryer opened to the right which has always been a slight inconvenience. . . So instead of changing out the broken part, I took the door and hinge off with my cordless screwdriver (6-8 screws) and turned it around and remounted it on the opposite side. . . Simple! I never took the new part out of the ups envelope. Now I have a spare so I taped the new part in the envelope to the back of the dryer in case I ever need it and now we have more convenience with the door swinging the correct way. Sweet deal! Took less than an hour. Thank you for making this task simple. Chuck g.

1.used small flat head screw driver to pop top of dryer. 2.used phillips screw driver to remove front of dryer. 3.disengage dryer belt. 4.take hold of brum and turn and pull out. 5.{left side}take snap ring,washer,roller off then remove support shaft. 6.install new parts, support shaft,roller washer, snap ring. 7,right side has a plastic washer that goes on before roller rest will be as step 5 8.put dryer back together.

The repair went well just unplug electrical cord then lift the top front edge of dryer top there are two 1/4 inch screws on the front top two corners take them out with nut driver or screw driver also remove the two wires that are connected to the switch for the dryer door the front of the dryer can be removed and put aside then at the bottom right corner of the dryer you will find the housing of the blower fan you will need to remove the front cover of the housing then put the housing front aside then take pliers and remove the blower clamp and then the retaining clip after that pull blower fan off and replace it with the new blower fan and the put everything back together It is really easy thanks parts select you had the parts for me

Basically I started off using youtube to see how to install. Two things to be sure you do – one the plastic washer only goes on one side (read the instructions)of the shaft and two the support brackets are not threaded so you need to use the original self-tapping screws. The screws that come with it will not work. Best to use a socket set to install the screws.

Ordered part ( door latch ) flowed instructions easily fixed same.

im a car mecanic it was easy

replaced belt first didnt fix the noise so i replaced rear drum support roller kit and that fixed the noise this was a cheap fix cost me about 70.00 dollars verses a new dryer thank you your website was a big help

First, I replaced the male end which was just two screws and simple replacement of pushing the fastener into the door frame. When finished I noticed the female end was damaged as well. Glad the female part came as well. This required taken off the front trim around the door (four screws - 2 each side) and then the door. The installing of the female end was easy with a little push. The damaged female end was already hanging out so easy to grab and remove. Otherwise I would have had to remove the front panel. Note You need to put the door trim back on before reattaching the door.