Models > 66598009701 > Instructions

66598009701 Kenmore Range - Instructions

All Instructions for the 66598009701
91 - 105 of 260
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Back left burner went out
I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.
Parts Used:
Element with Limiter 6 Inch - 1200W
  • Jane from BRYAN, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner did not heat up
Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.
Parts Used:
Element with Limiter 6 Inch - 1200W
  • Sergio from JENSEN BEACH, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the element was fried in half
only 2 screws held the element in place pulled the wires and replaced with the identical part very easy to do and thanks for having the part available
Parts Used:
Range Lower Bake Element
  • Rosemary from Louisville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element Wouldn't Heat
I removed the two screws that hold the element in place, moved it out to expose connecting wires, then removed wires and put in new element.
Parts Used:
Range Lower Bake Element
  • Lawrence from Lakeport, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Installed new element . Connected two wires pushed in place install the two screws.Done....
Parts Used:
Range Lower Bake Element
  • lou from spring grove, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower element burnt out.
This was really easy. I took out the lower oven racks. Most important - Turned off the breaker to the stove. Unscrewed the element and popped it out. Put in the new one and screwed it back in. Turned on the breaker and I was ready to go.
Parts Used:
Range Lower Bake Element
  • Cynthia from Ellicott City, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat from bottom element
First I disconnected the power! unscrewed the two screws holding element in place disconnected the wire clips from ends of element (be sure to hold them so they don't "retract" into the body of the oven) Connect the wire clips onto the new element and replace into original location and replace the screws. Turn power back on and start cooking again!
Parts Used:
Range Lower Bake Element
  • Douglas from WILMINGTON, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace lower element oven
once i got down and in the oven ( Im 74) that was the hard part all the rest was 10minutes and very easy ....... turnoff the breaker or unplug the unit
Parts Used:
Range Lower Bake Element
  • Edward from NORTH PORT, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LOWER OVEN HAD A CRACK IN THE ELEMENT
FOLLOWED INSTRUCTIONS AND READ THE HINTS FROM OTHER CONSUMERS. IT WAS VERY EASY.
Parts Used:
Range Lower Bake Element
  • Celeste from SAINT LOUIS, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element burned out
Took the element out & cleaned the oven & put the new element in. Easy as pie.
Parts Used:
Range Lower Bake Element
  • Deborah from PATASKALA, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
top broiler element burned out
I took the old one out and put the new one in. Even a woman could do it.
Parts Used:
Broil Element - Push On Terminals
  • James from Buzzards Bay, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Racks were old
Replace the racks. No special instructions.
Parts Used:
Oven Rack
  • Sandra M from DISTRICT HTS, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Parts Used:
Oven Rack
  • Linda from BURBANK, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The heating element broke
Unscrewed the old element. Screwed in the new element.
Parts Used:
Range Lower Bake Element
  • Stephanie from PFLUGERVILLE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Parts Used:
Leveler Foot Screw (Nylon)
  • Phyllis from BROWNVILLE, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66598009701
91 - 105 of 260