6651340592 Kenmore Trash Compactor - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dented front panel
The first panel I received was scratched and had to be replaced. I called PartsSelect and they sent a replacement.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
An easy replacement that made the compactor look like new, that is important since we will be selling the house.
Parts Used:
-
Michael from Southington, CT
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My very old trash compactor's carrier bag wore out
This new one from part select I think fit better than the original so all I had to do was install the handles as the depiction on the packaging showed and install it. Less than 1 minute.
Parts Used:
-
Jerry from CLARKSTON, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad gears and a bad switch
-
John from ALICE, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Roller was flat
Bought wrong roller. The drawer roller is different than the stationary rollers. Note the difference.
Parts Used:
-
John from Lancaster, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compactor draw was not opening fully as the wheel bearings had seized
I followed the you tube video instructions provided by customer care. This involved pulling the unit free from the cabinet, removing several screws that held the housing in place, this gave access to the wheel assembly, then I removed the nuts that held the wheel assembly in place. Fitting the new wheel assemblies was easy as was replacing the housing screws. After reinserting the draw and pushing the unit back into the cabinet it worked like new
Parts Used:
-
Andrew from ASHEVILLE, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rotary switch had finally worn out and was brittle and broken on our 30 plus year old trash compactor.
Removed the switch knob, the outer nut, and the front plate.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Unplugged the old switch from the 3 wires and plugged them into the new switch and put it back together with the new knob. Probably less than 5 minutes.
Parts Used:
-
Ray from MUNCIE, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trash carier wore out
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.
Parts Used:
-
Carmen M from Port Orchard, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compactor stop working
I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters.
Jack
Jack
Parts Used:
-
Jackie from Malone, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Jammed KitchenAid Trash Compactor.
With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.
I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.
I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.
I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.
I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!
Parts Used:
-
Jan from Gilroy, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
-
craig from OCALA, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front legs were rotted.
-
Cindie from DUNMORE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable), Wrench set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compactor won't stop
Remove the compactor drawer. Remove the front cover from the controls. TAKE A PHOTO OF THE WIRING TO THE EXISTING SWITCH! Remove the screw from the side of the switch and pull the switch out from the machine. You have to look very carefully at the switch to see the color labels on each prong of the switch. Attach gray wire to top prong (GR), red wire to middle prong (R) and so forth. Compare your work to the photo you took. Replace the switch, front plate and drawer. IT WORKS. YAY. Warning, my husband is dyslexic and attached the wires in reverse order and the compactor did not run at all. So, be sure you match wire to label.
Parts Used:
-
Jane from LUTHER, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ON RETURNING WOULD NOT STOP RUNNING
REMOVE COMPACTOR DRAWER
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
REMOVE SCREWS ON FACE PLATE
REMOVE SCREW NUTS ON PART (SOCKET)
SAVE HOLDING PLATE WITH SCREW NUTS
TAKE PICTURE OF WIRE CONECTIONS (IN CASE OF POOR RECALL
USE PLYERS TO PULL CONECTOR OFF OLD SWITCH
REVERS INSTALL
TOTAL 25 MINUTES
Parts Used:
-
Robert from DELAWARE, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers wore out
-
Charles from NEWBERRY, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All 4 compactor buttons were missing. The bag kept getting pulled down when we'd run the compactor.
I just used the accompanying screw to attach the buttons to the 4 holes in the drawer. Simple stuff.
I do think I read that the Jenn-Air bags used to come with precut holes, and the bag wold slide over the buttons, holding it in place. I jus get the bag lined up and pulled over the drawer, and cut the holes myself. It works perfectly.
I do think I read that the Jenn-Air bags used to come with precut holes, and the bag wold slide over the buttons, holding it in place. I jus get the bag lined up and pulled over the drawer, and cut the holes myself. It works perfectly.
Parts Used:
-
Paul from Amherst, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!