66513173K706 Kenmore Dishwasher - Instructions

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie

The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.

Removed the 10 screws holding the inner panel to the outer panel of the door. Removed inner panel to access latch/switch, then removed 2 screws to remove latch/switch. Then disconnected the 2 wires to the switch, connected wires to the new latch/switch and installed. Replaced all screws and voila, a working dishwasher! An easy 20 minute job with the help of the video.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

Watch video and followed instructions. Very easy!

removed and installed cords with screw driver

It was very easy.

Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.

Thanks,
Ted K.

First I replaced the lower door seal then I replaced the door gasket. The instructions were clear so both were pretty easy. Unfortunately neither fixed the leak. After further research I discovered that the screws on the pump had become loose. I used a torx driver to tighten the screws. Time will tell, but I am pretty confident that this has fixed the problem.

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete