58RIAD Whirlpool Refrigerator - Instructions

exact part in with the new out with the old

Followed video lnstructions which were very good. Have used your web site in the past and will continue to purchase products. Thanks.

I took the front panel off the ice maker. Found the contacts on control board were burnt. I called Partselect, told them my model # and they directed me to a new control panel. 4 screws later I had part back on and ice makin.
Thanks Partselect!

John Long

remove the wiring cover, pulled out the ice maker shelf, unpluged the wiring. Once out I removed the control module cover and remove 3 screws and pulled out the old control module. I pushed on the new control module and reattached the 3 screws, attached the module cover and plugged wiring in, slide back into the freezer track, installed wiring cover and screw- 15 minuits tops

Watched a video on YouTube on how to replace the icemaker control assembly. The video showed unplugging power, turning off the water supply, and removing the entire ice maker from the freezer. After watching the video several times, I unplugged the refrigerator but did not turn off the water supply. I did not remover the entire ice maker from the freezer, but I did remove the wire shut-off arm. After that, I pried off front cover of the control assembly. The control assembly is held in place by 3 Phillips screws; I removed the screws, removed the icemaker control assembly, replaced the assembly with the new one, replace the cover and wire shut-off arm, and plugged the refrigerator back into the wall. Had ice in about an hour (seemed the system had a little delay before deciding to go to work!).

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Removed icemaker by first removing the nutscrew that holds the cover to the electrical connection in place. Next, I removed the door then slid the icemaker out and diconnected the electrical connector. With the icemaker out, I R&R'ed the motor assy , reconnected the electrical, and slid the icemaker back in place. Next, I replaced the door, turned the icemaker switch on and waited. In about 30 minutes I heard the water being injected into the icemaker, and soon there was ice. The repair was easy and inexpensive. Tx to Partselect which I found on Google.

I unpacked the motor and looked at how it was supposed to go in. I removed on screw in the right rear of the ice maker. Pushed a tab on the left of the ice maker. Removed the entire assembly and unhooked the electrical part of the ice make. unscrewed the three screws holding the motor in place and replaced the motor. Put everything in back together and in 15 minutes the familar sound of the ice maker could be heard.

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

Removed 4 screws, pulled unit out of slots, unpluged control wires plug and removed from fridg. Removed 3 screws that hold the motor module to unit. Then reversed procedure and had the batch of ice cubes one hour and fifteen minutes from the time I started replacement.

Pulled off plastic cover on motor, removed 3 screws and removed old motor. installed new motor making sure control arm lined up in slot. be sure to disconnect power before doing this job !!!

replaced moduale, work just like new.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor assembly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs