Models > 58714439202 > Instructions

58714439202 Kenmore Dishwasher - Instructions

All Instructions for the 58714439202
76 - 90 of 310
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Latch broke
Six screws, two torque drive screws and, four wires.
Then reverse to install. Pull out old seal wash out groove find center mark on new seal and install be sure and fold notch on bottoms. Easy
Parts Used:
Door Latch and Gasket
  • James from Grass valley, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher hose had hole in it. It was 23 years old.
After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!
Parts Used:
Dishwasher Water Inlet Tubing
  • Shelley from LACONA, NY
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no issues
replacing 2 wheels was a breeze. did not need the screws afterall.
Parts Used:
ROLLER TUB Gray Kit - includes 8 Screws & 8 Washers
  • Rick from lees summit, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Latch Broke Off, Can't Close Door
Very easy to remove old broken door latch assembly, easier to install replacement. With door fully opened, I removed the 8 screws holding down the whole front casing, including the controls casing. Removed 2 Torx screws holding door latch assembly and then made sure that I marked all 4 wires before disconnecting them from door latch assembly. Connected wires to new door latch assembly, secured it with the 2 Torx screws, aligned and secured the controls and front cover casings with 8 screws. Done within 30 mins. Thanks guys for posting how-tos and thanks to PartSelect for a very fast shipping!!!
Parts Used:
Door Latch and Gasket
  • Giovanni from Glen Burnie, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was leaking water
The spray arm had become damaged on one side -- one side had apparently melted off. I replaced it, and it seems to have fixed the problem for now.
Parts Used:
Lower Spray Arm
  • Seth from Seattle, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing roller made it difficult to move rack.
The new roller just snapped in place.
Parts Used:
Wheel & Bushing Assembly
  • Racquel from Lake Charles, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Relay shorted out after diagnostics ran
Removed two screws on each side, lower half. Inside, removed six screws. Replaced the assembly and replaced all screws.
Not worth the fifty dollars for the part, just to have a door open at the right time to empty soap. Quite a hefty price to pay considering the price of the machine
Parts Used:
Detergent and Rinse Dispenser with Cap
  • Philip from Stafford, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed wheels for the roller part of dishwasher
Just snapped the wheels on and attached the bracket to the existing part.
Parts Used:
Wheel & Bushing Assembly
  • Jeanette from Fort Lauderdale, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing a wheel on dish rack
just slid the wheel on.
Parts Used:
Wheel & Bushing Assembly
  • Pam from Cherokee, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower repair arm failed and did not allow dishwasher to complete wash cycle. Repair completed in less than 10 minutes and dishwasher is now functional. Thanks.
remove center nut retaining the arm to the unit and replaced the arm.
replaced the nut.
complete.
Parts Used:
Lower Spray Arm
  • Donald from Prior Lake, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher racks would come off track
I clipped the wheels onto the rack. It couldn't be any easier. then i removed the # 25 torx screw which attached the broken slide wheel to the tub and installed the new wheel with the same torx screw.
Parts Used:
ROLLER TUB Gray Wheel & Bushing Assembly
  • chris from staten island, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken handle
Simple- Disconnect electric to washer, Remove inner door panel with philips screw driver, disconnect electrical wires watching exactly how they are to be replaced. remove star screws securing handle mechanism. Replace with new handle, connect wiring, replace inner door panel and your all set. Good luck.
Parts Used:
Door Latch and Gasket
  • Steve from Carrollton, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not stay closed
Followed the YouTube video. Replacement fit perfectly , only took 10 minutes to replace.
Parts Used:
Detergent and Rinse Dispenser with Cap
  • Niall from Schaumburg, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unable to add rinse aid
Screwed in
Parts Used:
Rinse Aid Cap
  • Jane from GREENFIELD, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door broken would not close
1.Turn off electricity. 2. Remove two Phillips screws on either side of front panel 3. Remove front panel 4. Remove 6 screws from the old dispenser 5. Pull both wires connectors from dispenser 6. Remove dispenser 7. Install the new dispenser and reverse the steps
Parts Used:
Detergent and Rinse Dispenser with Cap
  • gerald from MILFORD, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 58714439202
76 - 90 of 310