57731H6WW General Electric Washer - Instructions

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!

I dissasembled the machine and it took about 30 minutes. Orderd the parts recommended for noisy spinning. Reinstalled the new parts / changed all drum straps. Cleaned the drain drum and spin drum and after complete reassembly the washer is still noisy in agitation and spin cycle. The motor,transmission,counter weight,and drum look ok but there is still a reason why the machine is still noisy. Spent 120.00 dollars on parts so far but the drum and motor,transmission and counterweight are very expensive to replace. I am just going to keep using the machine until the washer fails to work anymore. I'm not going to put any more money in the washer. I will just buy a new one. It's not hard to dissasembled and reassemble the washer. I purchased the parts that was recommended to fix the washer but they were not the ones.The new parts did help like the tub seal but the bottom line is that the washer is still noisy. I watched your videos to work on the washer and there were no special instructions on disassembly and reassembly. Like always there must be more than i know to repair this washer. Thanks

Turns out that water valve was bad but that's not the only thing I find out after I replaced that part my washer could not register what load size is on so there is bad pressure hose and pressure switch also. Easy unplug washer turn off water remove water supply hoses then unscrew the 3 screws that are holding control panel. Disconnect old valve from the cable plug unscrew the screw that is holding water valve. Install new valve by placing it in the same place where the old one was screw the screw that holds the valve connect it to the cable plug connect water supply hoses plug plug in the washer back and turn on the water. Check for possible leaks and test your washer by choosing the smallest load.

There is a metal plate on back of the top of the washer held on by 3 screws. Removed them and that gave you access to the water valve. Water valve was fastened with 2 screws. Removed them and the hose that was connected with a clamp. Reversed the order on the installation and done. Whole job took 20 min. Now I know where to get parts. This site was awesome. Ordered the part on Tuesday, UPS delivered Thursday.

There is nothing to tell really. Took the setting knob off, put the new knob on. That was it, took all of five minutes.

Unscrew the 2 screws holding the drain hose clip to the machine - use bucket to get an excess water - remove bad drain line - I installed a new drain hose clip as well - make sure you put the clip on at the same position as the previous hose - push house firmly into opening and screw into machine - pretty easy repair - and I'm a novice

After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.

after ordering part and getting the wrong part sent to me i was able to finally get right part to my house 2 weeks later, i pulled front cover off with a screwdriver took out broke rod and inserted new part closed cover and hooked power back on and was in business

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.