41729042991 Kenmore Washer - Instructions

I removed the 2 screws holding the original door catch and simply replaced with the new one, replaced the 2 screws and that was it!

I simply removed the two screws holding the existing (broken) catch and replaced the old with the new in less than 5 minutes. It could not have been easier.
I would alsolike to note that I was VERY pleased with how simple it was to find the correct part and with how quickly the part arrived at my door. I will definitely refer PartSelect to anyone who may need a new appliance part.

I removed thescrews , removed the roken part and then placed the new part in replaced screws , done in under 3 minutes

I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

I found a person on youtube that had a similar issue with a Fridgidaire washer. Since my Kenmore was quite similar, I was able to see how the installation would take place. I bought the new motor from Parts Select, and when it arrived, the steps needed to repair the washer was:
1) Unplug the washer
2) Turn off water supply at the wall for hot and cold water
3) Pushed washer away from the wall.
4) Remove the water supply hoses by unscrewing them on the washer end. These were on tight, so I needed to use pliers to unscrew the hoses.
5) I removed the multiple screws on the back panel of the washer. I think there were 12 or 16 screws.
6) Once all the screws on the main panel in back were removed, I removed the back panel and set it aside.
7) I located the motor near the bottom of the tub and removed the two slide-in type electrical connectors. There was also a grounding wire, and I left it attached at this point.
8) Using a socket set, I removed the four screws that mounted the motor to the tub.
9) Once the four screws were removed, I was able to push the old motor back about an inch so the motor was no longer on the sleeves that held it in place, and I pulled the motor toward me. The grounding wire was still connected at this point.
10) Once I was able to get the motor to the back of the washing machine, so I could see it, I could then use a star-screwdriver to remove the grounding wire.
11) Then I went through the same steps backward to install the new motor, which matched the old motor exactly. The time from when I started to when I was completed was about 1 hour and 15 minutes.

The video was most helpful, and the left shock replacement went as shown. The sucker punch was getting to the right shock - much harder.
First notice video has washer on a stand. How nice to have had it up on a table. LOL As it was I tilted the machine back with a 6 inch block under the front. Still a bear to get to the shock, but w/ patience, doable even though you are flat out on the floor.
The old shocks were so bad that the pistons fell out once it was removed.
It takes some strength to get the pins through the new shocks, and as I have a weak left hand I had to resort to using a C-clamp to help. If I could have gotten my right hand in there I may not have needed it. Right hand did have to hold the clamp as it had to just catch the side of the pin hole since the pin is pointed and sticks out past the mounting bracket when seated.
I also ordered a spring but they both were still good.

The instructions that come with parts say to pull pins out with pliers. not much room to do that. I used hammers and punches where I had access and prybars nail puller an hammer to offset where the water outlet was in the way. I used a short handle hammer to install three of the pins. The third I used a prybar and spacer blocks.

Removed lower access panel. Removed top of washer. Attached spring and lifted tub into place. Removed and replaced both vibration/shock absorbers (most difficult part, not easily accessible).

removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.

I replaced both shocks, as both shocks were broken! Keep in mind that Parts select packages them in pairs. I order 2 packages or 4 shocks, guess I have another pair for ~ 5 years from now. These are located under the front bottom panel, so no need to isolate water lines or even pull this sucker away from the wall. Tight clearances are the only factor from making this really easy. Use some Vaseline to assist inserting the new plastic pins.

we took the hoses off then unscrewed the bracket that was connected to the part and then once out we put bracket onto the new part and screwed it back to the washer connected the hose back and WOW the water was flowing

I looked up the repair on You Tube and it looked easy! Take off the top of the machine (unplug and disconnect water first), 2 wire connections and 2 screws to mount. The only problem I had was screwing the mounting plate on the machine. It needed some help enlarging the hole a tad, I used an awl. Reconnect the water and plug in.This Granny rocks!

Pulled the locking pins out, replaced the shock absorbers and re-installed the locking pins. I used Channel Lock pliers to remove and replace the locking pins. i used a deep socket to hold down the tab on the locking pins so they could be pushed out. The new shock absorbers came with installation instructions.

Remove front panel to expose shocks. It took some time to remove the old shocks, both were broken. The pins were somewhat difficult to reach and remove, especially the one on right for it was shoved up against the electric wiring box. We ended up putting that pin in backwards for the new shock because it was impossible to reach from rear. Putting the new shocks was easy it was removing the old ones that took most of the time. The washing machine is working perfectly now.