Models > 4071510 > Instructions

4071510 General Electric Dishwasher - Instructions

All Instructions for the 4071510
106 - 120 of 332
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower wheels kept falling off
Installed new lower rack wheel kit
Parts Used:
Lower Rack Wheel Kit - 8 Pack
  • helmut from EAST KINGSTON, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost cap to rinse aid disoenser
Just screwed it on.
Parts Used:
Rinse Cap Assembly
  • MarilynNegri from BLAIRSTOWN, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse aid cap leaking
Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found
Parts Used:
Rinse Cap Assembly
  • David from BURKBURNETT, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Parts Used:
Hinge Arm Link
  • Ron from SOUTHPORT, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Parts Used:
Dishwasher Dishrack Rollers and Axles
  • Wayne from PALMER, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishrack was worn and causing chips on dishes
just slid the new rack into place
Parts Used:
Dishwasher Lower Dish Rack with Wheels - Gray
  • Kathleen from LOUISVILLE, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Parts Used:
Detergent Dispenser with Rinse Cap
  • Michelle from Carlisle, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch broke
took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe
Parts Used:
Door Handle Actuator Recess Door Spring
  • Joe from Clinton township, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishes where not clean after washing
change the nozzles and filter
Parts Used:
ARM SPRAY UPPER Assembly Lower Spray Arm - Gray Middle Spray Arm Fine Filter
  • Daniel from Maurice, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
7 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We had a rip in our tub gasket.
I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!
Parts Used:
Tub Gasket
  • Estelle from Queen Creek, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top rack had the plastic coating coming off
Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance
Parts Used:
Upper Dishrack with Wheels
  • Chester from North Las Vegas, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Parts Used:
Detergent Dispenser with Rinse Cap
  • KEVIN from MACKINAW, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Parts Used:
Dishwasher Rack Slide End Cap
  • Cindy from Davidson, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Parts Used:
Dishwasher Rack Slide End Cap
  • Daryll from Newville, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Toe kick was misding
Screw on the part.
The one screw was too expensive and o thought when I ordered it the package said 2 screw for $14.99 but only came with one screw.
We found an screw that worked.
I suggest the toe kick to include the 2 screw to make the experience of DIY easier
Parts Used:
Shoulder Screw TOEKICK Assembly
  • Elahe from SAN JOSE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4071510
106 - 120 of 332