3RLEQ8033SW0 Whirlpool Dryer - Instructions

It's a electric dryer, I knew it was related with the thermal !

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Ezee pezee lemon squeezee.

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Took, back cover out,but first i disconect the electricity,i give a fast look,looking for anything wrong and i saw a thermostar burn out in the element case,the bottom one,a thermostart
250 f. but a did a search in the internet,and found that when a bottom thermostart burn out, the top one had to be change,so i did a continuity text in the top one and was open ,i have it,a used one, change and connect the dryer to the Electrical outlet and (walac)it start the dryer,problem solve

Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it

Replaced 4 wheels and new belt

Remove old filter
Vacuum out
Install new filter

The repair was no problem. Just taking off the hex screws removing the crimp wire and replace the parts in the kit and the old dryer came back to life again.

Thanks

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

all that was required was to push the catch into the slot notools needed.

Unplug the machine. Take off back panel and remove heater assembly. Since I was already into the heating system, I replaced the heating element as well ($30). I replaced the old thermal cut off and overtemp, put the wires back on the connectors, reassembled, and the dryer works like it did when brand new! Within 30 minutes the repair was completed. Still saving for a new front loader washer/dryer, so the repair will hold us until we have enough to buy new. Alos, helped us to need to dry clothes on a clothes rack in the house. Good practice and lesson for the entire family!

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.