3RLEQ8033SW0 Whirlpool Dryer - Instructions

Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done

Replaced the thermastat first, then the cutoff switch, still the same, I then replaced the thermister, and still have the problem.

Old door catch came out, new one slipped in. All works great.

Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.

I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.

I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary

Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyone.

I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

had to take front off of Dryer then was able to replace drum roller