3639754581 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice maker quit makeing ice
Wathched the video and it was done in less than 15 min making ice again no problem
Parts Used:
-
Dickei from Sugar Land, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Gears were jammed, and broken when jam was cleared causing them to make loud knocking noises when spinning
Popped off the old gears with a screw driver. Put on the new gears with a screwdriver. Problem fixed in less than 5 minutes.
Parts Used:
-
Nathan from Coralville, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No problems.
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.
Parts Used:
-
Patricia from Norwood, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Parts Used:
-
Charles from Edmond, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Parts Used:
-
Bob from JASPER, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not make ice
i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess
Parts Used:
-
jeffrey from clinton, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker kept on making ice
I ordered a new micro switch that was activated by the high ice lever. Once the switch was replaced the ice maker cut off as it should have and stopped producing too much ice. YHis job was of moderate skill level, the most challenging was replacing a spring that popped out then reassembling the unit.
Parts Used:
-
Michael from Santa Fe, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no ice
-
Richard from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Was not making ice
Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen
Parts Used:
-
Colleen from Yorba linda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!