36371542211 Kenmore Washer Dryer Combo - Instructions

Pulled the drum an found spade clip burned on wire. Hi limit Thermostat crumbled/ broke while pulling spade clip so I trimmed back the wire, cleaned the spade clip and soldered the wire back on. Isolated the other thermostats in the system and tested for resistance. Reassembled dryer.

Good thing my husband is so handy. This part was very difficult to get to. Basically, he had to take apart almost the whole dryer. There is no access door so the side panel had to be removed, but before you could do that the front panel and door had to come off, then the top of the dryer. Keep track of the screws, we had a few leftover! But the dryer works great again and we hope to get several more years out of it. We've had no problems with it until now and it's over 15 yrs. old.

loosened two hose clamps and four screws to replace the anti siphon valve.

Parts were easy to take out and replace with the new ones.

By watching your video which was very helpful as I never made this repair before. All worked out fine. Since then I have ordered other parts., (drum bearing kit, door slides and a new belt.) The video on replacing the drum kit is very helpful too. One other fact is prices beat all other sites I looked and when I'm done the dryer will be "rebuilt" I recommend your parts to everyone., they are great quality.

Replacing the front slides is easy. Just buy the parts and pop them in. The rear drum bearing is also easy, and you do not have to spend $50. Once I had the parts in hand, which is an axle from the rear of the drum and a bearing sleeve from the rear of the dryer cabinet, it looked quite simple and it is. I went to a hardward store, bought a bronze bearing that fit the axle and the sleeve and a C-clip. Cut the bearing to the correct length with a pipe cutter, and retain over the axle with the clip. Grease it up, and put the dryer back together. Total cost, $5. It works great.

removed top, 2ea screws ;removed front door,2 screws; removed left side panel,screws on bottom and back; removed belt,pulled out drum. replaced top drum bearing,installed green and white slides,re assembled w/ new belt,ops. check ok.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Removed 2 screws to remove top. Removed 2 other screws to remove front. Removed old parts. Installed new parts. Reassemble all afetr cleaning duct work out.

open door, remove two screws from below the top. gently remove the top from the side and bottom panels. remove two 5/16 screws from front panel hold panel so it does not fall. the bearing assembly will come out by moving the bearing towards the dryer, and pulling upwards. replace with new bearing, use 4 front dryer slides and reinstall the top and front panel. can be done in less than 15 minutes

The parts came very quickly, and they were the exacxt parts which made installation very easy.
Just open the dryer door, there are 2 screws to remove right above the dryer door that holds the top plate of the dryer. slide the top of the dryer top off by pulling up and ouyt towards you. There are 2 screws that hold the front of the dryer, remove the 2 screws and the front of the dryer will come out towards you. The drum will fall a litttle towards you.
I let the dryer front lean on my leg and snapped out the bearing and drum slides replaced it with the new one. Reverse the order of taking it apart
Now my dryer sounds as quiet as the first day I bought it.

We had a squeeking sound coming from our dryer which I felt was probably the belt. When I removed the front of the unit and saw the condition of the slodes and drum bearin, I ordered a set from PartsSelect.com. It only took about 20 minutes to repale the parts, and 5 of that was figuring out the bearing just "snaps on" (I was afraid to just yank it for fear of breaking something else). Probably saved like $75 or so between the parts markup and a service call by doing it myself.

Unplug the dryer. Remove top panel (remove two screws on the upper inside edge of the dryer door). Lift the front panel from front (tabs and slots at the back) and lift off. Remove the front panel (remove a screw from each side - top/front). Front panel sits on two feet at the bottom, tilt it forward from the top and lift it up (careful not to damage the electrical connection at the bottom left side). I found the dryer had another damaged part (plastic guide that the Slide WH and the Drum Slides connected to was badly worn). After ordering the additional part I attached the slides (white and gray) to the guide. Set the front panel back on the two feet and tilt it back into place (you'll need to slightly raise the drum back into position - easy). Replace the two screws that connect the front panel. Replace the top cover. The whole repair took less than 1/2 an hour including the time it took to vacuum out the dust. Total cost, about $35!

inside dryer door housing i removed two screws these hold top of dreyer on.pulled dryer top up and it unhooks from control panel.theres two more screws inside the front door asembly located at the top on booth sides.remove them and the front is free except for dryer door switch.lean it back far enough to unpug wires.lay door asembly on the floor.drum slide pops out with screw driver at the top the bottom just slides out.drum bearigs are plastic strips on the drum slide. pull the old ones out if their is any left.replace with new.you need four drum bearings.then put back together the ame as you took it apart. good luck terry

The gentleman knew what the problem was, sent the right part, and I looked like I was smart.