36371542211 Kenmore Washer Dryer Combo - Instructions

watched vidio from the site.just follow the instructions, And was able to fixed the problem.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

I followed the instructional video that was given online. The parts fit well, and was easy to repair.

Remove the old bearing assembly and Replaced with the new bearing assembly with new bearing slides.

I followed the video instructions provided to me by this site

remove to screws in front to take of top. Then remove two screws holding the face on. change parts re assebmle. extra hands nice for holding drum while remounting face. Nice and quiet now.

The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple ... Read more plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.

Follow the instructions from YOUTUBE to replace the new drive belt..

After unplugging the dryer, I removed 2 metal screws up under the dryer sill rim, and removed the dryer top. Then, removed two more at the top of the front (door) section to remove it.

I wasn't careful enough when removing the door, and the wiring connectors popped loose from their connections. No harm done, though. Disconne ... Read more ct the wires once you remove the front panel.

I had to loosen the bottom metal screws on one side panel to have enough give to pull the dryer drum out.

The only way to replace the belt is to bend over the side of this unit and with one hand put the belt around the motor drive shaft, pull the tension pulley back, and put the belt on the wheel.

The hard part is working the drum back into place while VERY carefully slipping the belt into the drum goove. Many attempts were made only to have the belt slip off of the tension pulley or motor driveshaft. Be care full to turn the drum clock wise if the belt twists while working it into the drum groove. It was very disappointing to finally get the belt on, and work the drum back into place only to discover I had twisted the belt with the smooth side making contact on the driveshaft. Thus, I started over.

Aiming the drum into the back of the dryer is a tough task. I recommend a 1" X 4 " X 12" board to slip under the drum when beginning this process to help stablize, and guide the drum. It helped me tremendously, and was easy to remove out from under the drum once everything was back in place.

Use gloves. Yes, tough to work with in small places, and I did take them off to replace the belt around the tension pulley, however, there are too many sharp edges on the metal body of the dryer and especially the drum to do so without gloves.

Wires were easy to reattach and reassembly was smooth except for the top...check out the tabs, and spring tabs before you try and just plop the top back on. It goes a certain way...You'll know what i am talking about when you do this task.

I truly hope you have L O N G arms to do this task, and that the new belt lasts a long, long time!

I followed the directions I found on my tablet on youtube.

Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.

It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.

If I were to do it again, it would take 30 minu ... Read more tes or less.

Removed two screws inside the door at the top of the frame. This allowed the top to be lifted and slid to the left a bit which allowed the front of the dryer to be removed. The Drum Bearing was held on with plastic tabs and the Bearing slides just fitted over a small tab then into a slot. There is a "knockout" for the light which is re ... Read more moved. The entire process took less than 15 minutes.

Looked at the diagram on your web site and replaced part

TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY

Unplugged power to dryer. Opened door and removed the two screws that hold the top panel on. Removed top panel and set aside. Then removed the two screws that hold the front panel secure and leaned front panel towards me. Replaced parts with absolutely no tools. Reverse steps to assemble dryer. The videos are very informative and give you ... Read more the confidence you need to do it yourself.