All Installation Instructions for Kenmore Refrigerator 363686

sweating

i found that the door was to low was the problem shimmed the hinge on the bottom brought the door up so the gasket was ok so isent the new gasket back to you never attempted to change so i dont have any thing to tell you about instalation difficulty carl phillips

Parts Used:

Fresh Food Door Gasket

carl from zephyrhills, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 9 people found this instruction helpful.

Was this instruction helpful to you?

light in freezer section not working

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Parts Used:

LIGHT SWITCH

Victor from Fort Myers, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 24 people found this instruction helpful.

Was this instruction helpful to you?

The bottom part of fidge was warm with water droplets on the its ceiling.

Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart brackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.

Parts Used:

Evaporator Motor Kit

Charles R from Renton, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

not cooling

refrigerator was not cooling. with new fan the refrigerator is working so well I had to turn it down to "1" to get the temerature right.

Parts Used:

Condenser Fan Motor

cyril from holden, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

refig light did not work

per your instructions

Parts Used:

LIGHT SWITCH

paul from east hanover, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Noisy fan

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Parts Used:

Evaporator Fan Blade Kit

Robert L. from Eldred, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Fridge not cooling

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

Parts Used:

Condenser Fan Motor - 115V

Pedro from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Replacement gasket

I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit

Parts Used:

Freezer Door Gasket

Dewey from Laurel, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

switch wouldn't come out anymore and turn light on

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Parts Used:

LIGHT SWITCH

Cynthia from Seatac, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

lost screw and insert plug

replaced the screw and covered it with the plug. The pleasant surprise was that the requisite screw plug were available, especially after over 10 years.

Parts Used:

Screw

Plug Button Insert - Almond

BENNIE from KNOXVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

no light in freezer

Connected the 2 wires and pushed in the switch until it clicked.

Parts Used:

LIGHT SWITCH

christopher from collegeville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Reistall shelf

Replaced cap and reinstalled. But I used iron nail inside cover to hold right side because crack was at right hole and right part would not help.

Parts Used:

Door Shelf End Cap - Left Side

Oleg from Lees Summit, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

needed new light socket

Pulled out old socket.pushed in new one.

Parts Used:

Light Socket

Charles from Williamsburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

broken crisper drawer support

quick and simple--removed the old one and slid new part in on same support pins.I had the new part via UPS LESS THAN 24 HRS.FROM THE TIME I PLACED THE ORDER! THANKS, SOMEONE IS REALLY ON THE BALL.

Parts Used: