363595 Refrigerator - Instructions

Unplugged frig. Turned off water supply to pump. Removed black cardboard covering on back of frig with nut driver (6 screws).

Took digital photo of assembly to confirm reassembly position.

Removed copper waterline to pump with adjustable wrench. Removed 1 screw holding pump assembly to refrigerator. Pulled assembly out of the frig. Unscrewed two small black screws on a second bracket. Pulled old pump further out of frig. Unplugged two connectors. Removed plastic waterline from pump by turning hose counter-clockwise and gently pulling.

Inserted plastic water line into new pump by turning line in clockwise and it pushing into orange plastic stop. Reconnected two electrical connectors. Reconnected bracket to pump with two small black screws. Gently pushed assembly back into the frig and reconnected pump assembly to the frig with 1 screw. Reconnected copper water line to pump first wrapping threads on pump with Teflon plumbers tape.

Turned on water to check for leaks. Installed cardboard back on frig with 6 screws. Plugged in frig.

NOTE. My new pump assembly had the electrical connectors reversed. Take care to pair up the correct colored connectors.

The replacement ice maker that GE supplies for my old refrigerator is a little different than the original. The electrical plug changed from a round plug to a square one. They include an adapter for it, but DON'T USE IT. There's not enough room for the bulky cord and connector. I got a much cleaner installation by taking apart the old and the new ice maker, and then splicing in the old connector into the new ice maker. You need to carefully unscrew a circuit board inside to wire it in, and it'll be more secure if you solider 3 wires instead of using crimp connectors. The instructions also tell you to use your old 'ice breaker', but it won't fit on the new ice maker. I just left the new ice maker's ice breaker on, and it seems to work perfect.

Unplugged refrigerator from electrical outlet for safety and turned off water supply valve. Removed the four metal screws that hold the access cover on the rear of the refrigerator. Then removed single metal screw attaching water valve and bracket assembly. Unplugged wire harness from the water valve and assembly then pressed down on colored o-rings to detach the four plastic water lines from the water valves. Used open end wrench to disconnect main water supply line from the water valve.
Pressed down on colored O-rings to install the four plastic water lines to new water valve and bracket assembly. Wrapped plumbing tape on threads of inlet valve and and used open end wrench to attach main water supply line to new water valve and bracket assembly. Attached wiring harness to new water valve and bracket assembly. Mounted new assembly to refrigerator with single metal screw. Turned on water supply valve and checked for leaks. Plugged in refrigerator to electrical outlet and tested water dispenser. Replaced access cover on rear of refrigerator with four mounting screws.

Frig and freezer were defrosting and refreezing other than normal. Home warranty contractor told me ice maker was faulty. Purchased new ice maker. Unplugged frig, loosened 2 screws with nut driver. unplugged old ice maker, lifted old ice maker out. Took old fill cup off old unit and put on new unit since new fill cup was a different size. Swapped ice maker insert from old to new unit. Plugged in new ice maker, slid over the 2 screws, tightened, and plugged in frig power. New ice maker works fine but still have defrosting and refreezing problem. Figure old ice maker probably works just fine. New contractor still trying to solve problem. Have had problems with this GE Monagram keeping proper temps since it was new in 2005, don't recommend it.

Unplugged refrigerator, removed three screws to take out part, disconnected the wires and removed bad unit. Removed fan blade from old unit and attached to the new unit. Attached wires, placed the new motor back in. Plugged it back in, within 20 minutes panel between freezer and refrigerator was cool to touch.

Removed the face plate this just gets popped off. removed the four screws to release the unit. unplugged the wiring harness, removed the two screws that hold the bracket in place that the control unit is housed in. Slid the old unit out and replaced with the new unit. installed the bracket over the control unit put two screws back, plugged the wiring harness's back in. Slid the whole unit back in replaced the four screws and put the face plate back on. Very Easy.

i turned off the fridge and unpluged it , took out all the shelfs in the freezer and took off the back panel to get to the heater , the heater is only held in with 2 screws and unhook the 2 wires and replace the heater , and then thermostate is on top of the coils , i just cut the 2 color coded wires and replace the theromstate , was easyer then i thought ,

I had to completely disassemble the ice bucket (dispenser) to gain access to the parts that were being replaced.
*
It was helpful to have the exploded parts diagram to aide in reassembling the ice dispenser when replacing the parts.

The leak was obvious and I took out the cardboard backing. I closed the valve (water supply) to the water dispenser and ice maker.

With the screw drivers and socket set, I was able to take out the old valve and disconnect the hoses.

Since the part was identical to the leaky valve it was just a matter of reversing the steps. I had previously researched on the web to find the identical part and found a match at Partselect.com. I wish all my repair attempts turn out to be this easy. I wish GE had used better parts since this incident has set me back by several thousand dollars due to the water damage to the wooden floors, basement ceiling and walls.

This problem had already occurred in 2008. Repairman replaced dual water valve. Cost $190.00. We decided to do it ourselves this time. The repairs were actually made in three phases. First, when I pulled the fridge out from the wall, unplugged it, and turned the water valve back on I discovered that the plastic tubing from water supply into the fridge had long cracks in it and water was spraying out everywhere. I turned water off, went to Lowe's and bought the kit for that repair. Of course I didn't have to use all of the parts in the kit because the water supply was already there from the valve that came up through the floor. After turning the water back on and plugging the fridge back in, my husband and I tested it by trying the water dispenser. We found that water was leaking from somewhere inside the fridge, but didn't know where. After UNPLUGGING it, and turning the water off again, I took the metal back off at the bottom. It was leaking from the bigger plastic tubing (5/16"). It was just hanging, not connected into the dual water valve. Figured it had just broken. So I thought I just needed 5/16" tubing. I went on the GE website and it was very hard to get answers to my problem because I couldn't find the plastic tubing that it looked like. I ended up ordering the plastic tubing that goes up that back of the fridge to the icemaker. They sent me two of those, not one for the freezer and the bigger clear one (5/16") that I thought I needed. Then, I found this website! This PartSelect website is great!! After reading about other consumer repairs, I knew how to disconnect the dual water valve and found out that the smaller plastic tubing that goes up the back of the fridge to the icemaker had been pinched where it connects to the dual water value, barley hanging on. Just quick disconnected it from the valve by pushing up on the outside where the tubing comes out while pulling on the tubing. It came out, and I had to use needle nose pliers to pull some of it out where it had broken off inside. Then, pushed the new tubing into the valve and ran it up the back of the fridge, unscrewed the plate that goes over the clamp that holds the tubing, loosened the clamp a little, pulled the old tubing out, pushed the new tubing in, (the clamp was still tight enough) put the metal plate back on and replaced the screws. Then I re-connected the dual water valve to the electric clips, connected the 5/16" tubing to the right side of the valve. (The black tubing that goes up the back of the fridge goes into the left side of the valve.) put it back into place and screwed it back against the body of the fridge where it goes, put the back on and plugged it back in. We tested it again, and water was leaking, but not from where I made my first repair. I reversed everything again, and discovered that where the 5/16" tubing goes into the dual water value, it seemed more loose than it should have been. That is where the water was leaking from! I ordered the dual water valve, the 5/16" plastic tubing and the water tube union. I replaced the dual water valve-very easy! MAKE SURE YOU UNPLUG THE FRIDGE, turn the water supply off, disconnect the small tubing from the dual water valve, disconnect the electric connections to the valve, and reverse the process. What I did was replace the 5/16" tubing the comes out of valve & goes up into the storage tank behind crisper drawer. Used union there. Put everything back together and it works!!

Isolated water line. Remove water valve from harness. Disconnect water connections. Disconnect electrical connections. Removed valve. Installed new part. Reconnected water connections and electrical connections. Opened water line.

First turned off power and removed top shelf.
Then I used a flathead to slowly pry the switch out by the two sides. You just anlge ita bit and it slideds out easily. Then I disconnected the wires from the old switch, connected the new one and installed the new switch by snapping it back into the cutout.

unscrewed old filter by hand, installed new filter.

Unplug the refrigerator. Move things to gain access to the bottom back of the refrigerator. Take care in movement of refrigerator not to kink or loosen the ice maker water supply line. Use nut driver (best), screw driver, or socket to take off 6 screws holding the cardboard cover (air access for the fan). Remove the old fan blade with fingers and light pressure with a screw driver, it will snap right off. The new blade comes with a ringed compression fitting so you need not buy the new one that is shown on the schematic diagram. Push the new blade on the fan shaft far enough to allow the shaft to protrude from the front side of the new blade-that is what holds it in place and you should feel a little snap when it is inserted far enough. Caution: Do not vacuum around the blade or try to reinstall the cardboard cover while the fan is running. I broke two of them while doing just that, they are very brittle. Recover with cardboard and you're done!

First I turned the freezer off and took out all of the shelves in the freezer section. I then removed the guides that the shelves go into. I removed these only from one side of the freezer - the left side actually. Now I removed the plastic piece that keeps the bulb in the freezer protected. Removed the bulb. Removed the three screws on the top and the two in the bottom that keep the rear panel of the freezer attached. This exposed the header cable and the coils. The coils had ice on the lower section, I used a hair dryer to melt the ice. Removed the cable assembly that has the two heater elements and the thermostat. The thermostat had to be plucked off the the metal pipe of coils. Replaced the assembly with the purchased assembly. Clipped the thermostat onto the metal pipe of the coils. COnnected the wires at the white connector. Attached the real panel using the five screws, put the bulb back in, installed the bulb cover, installed the shelf guides, put the shelves back in.

Freezer freezes very well now.