31213WAV Magic Chef Range - Instructions

USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.

Very easy, video helped tremendously

Unplugged two connectors and plugged into new burner. Couldn't have been easier! Also, I was so pleased that it matched the other three burners exactly!

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Turned burner about 1/16 turn to left. Lifted burner from stove. Disconnected two wire connectors. Connected same wires to new burner. Set burner in place and turned 1/16 turn to right. Tested burner. Lighter worked on first attempt and burned perfectly. Took about 3 1/2 minutes.

Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped.      Thanks   Lloyd

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.

My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....

took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....