31213WAV Magic Chef Range - Instructions

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

Unscrew the burners an install new ones! Anyone could do this.

Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.

I took the broiler pan out of the shipping container and put it in the oven.

Went well

I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!

Remove oven door, remove burner bar, replace ignitor, splice wires together because the old electrical connectors had melted together. Shipping was fast and extra wire, insulation and ceramic wire nuts were included.

My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

Removed grates and bottom plate two screws holding it. Turn oven light on and unwire the wire. Unscrewed the two screws and replace. This took my husband about ten min. And for him he says that this was a walk in the park. He says if he can do it anyone can. This was one of the easy honey dews. Good luck with yours. Nola & keith

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

The repair was a simple replacement, no tools needed. The old burner and grate came out as easily as the new parts went in. PartSelect Customer Service Rep D. Hanham helped me find and order the correct grate. Great Customer Service!

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!

I followed the video and it was incredibly easy. I shut the breaker off (we live in an apartment, and pulling the plug on the stove wasn't possible). I lifter out the old burner (the gasket underneath was corroded, and I just threw it out, as the newer burners are self-sealing); removed both the igniter wire and the ground wire (I needed a pliers to tug the igniter wire off); attached the new burner; replaced the burner; turned on the power; and voila!