2661532513 Kenmore Washer Dryer Combo - Instructions

Replaced with the new part that I ordered from partselect.The washer works good. Thank you.

I used these two videos to help me clean the inside of the machine, then change the drive belt.

We watched the video of how to take the dryer apart and how to install the thermostat...after watching the video it was pretty easy

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Parts arrived well in time, exactly what was needed. The latch was a snap-in process. The strike require gentile use of a pliers, and went in quickly. Thanks!

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.

Switch off the circuit breaker supplying power to the dishwasher.

Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.

Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.

Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.

Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.

Snap the switch (or switches) back into place in the cradle.

Replace the spring activator along with the plastic sheeting and screw that back in.

Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.

Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.

Switch the circuit breaker back on and give it a whirl. Enjoy!

Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.

I only had to replace the "plastic" knob on my dryer. This required no tools- just push on to the stem. This part needs to be improved... should be made out of something other than plastic because this gets a lot of wear. I was very pleased with how fast I was able to order & receive my part shipment. I shopped around for this part & your company beat any other price on the market. THANKS!

Removed door strike and latch, replaced, works like new.

inserted the latch into the opening in the front face of the dryer