2490 - Instructions

First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.

order a new try and install

Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.

Got a RobertShaw part from PartSelect and now the burner works perfectly.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

Removed the rubber gasket and checked the switch. The switch displayed signs of scorching and the plastic was very brittle. Removed the switch which was held in by a small bracket and one screw. Replaced switch on bracket and remounted the switch. It took longer to reinstall the rubber gasket that to diagnoise and repair the switch. This was a very easy repair and the time from the part order to receiving it was two days. I'm very pleased with the part availability and quick shipping.

Simply pulled the old ones off and pressed on the new control knobs. It took less than 10 minutes, saved us from replazcing an otherwise nice looking range top, and made a big deposit in my "Honey do" account. I just wish they still sold the clock and timer units to fit this stove. Oh and yes, the prices were very reasonable too. Thank You Brad Harris, Illinois

Very easy. Pull out refrig from wall to access the rear, turn off ice water line and Unplug refrig from wall outlet. Take socket and unscrew the one (1) tap holding the unit.
Remove the electric conections, pulling out from unit (there is nothing holding it in place but friction).
Remove the main water tube (have papber towel for water drip, there will be some)
Remove the two water tubes on top of unit (noting which tube goes to which relay)
Reconnect electric connectors to the new unit, reonnect water tubes to the new unit, screw down the new unit.
Turn water on and plug refrig back into AC outlet.
That's it, 20-30 min.

removed two screws thenpulled element up unpluged wires

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

I unboxed the new drawers, measured and cut some 1/8 plexiglass strips to fit. I then glued the strips on the inside of both drawers to strenghten. The original and replacement drawers lack strength at the corners and crack. This was the third set I have replaced. Should not happen again.

Turned off power at breaker. Removed screws holding control knobs in position. Removed knob and unscrewed nut holding switch in place. Noted wire positions and undid connections. Connected wires to new unit. Replaced nut and screws and control knob. Restored power and checked operation. You can do this. Don't call an electrician.

Our 20+ year old Maytag refrigerator suddenly started dispensing water one day without anyone near the refrigerator. Thankfully, my wife was nearby; my son temporarily solved the problem by shutting off water to the house. The ice dispenser unit has a "Lock" switch which turns off power to the ice & water dispenser. With the switch in the "lock" position, we were able to continue using the refrigerator (and turn the water back on) until I was able to get a replacement part.

The biggest hurdle that I encountered was removing the trim; I spent perhaps an hour and a half trying to figure it out. In the end it turned out to be easy and would have been perhaps half an hour job total had I known the trick. So... to remove the trim on a Maytag RSW2400, you remove a single Phillips head screw on the bottom of the trim. The trim then slides to the left and can be removed.

The next mistake I made was removing the entire dispenser unit. Instead, if you look closely, there are screws which may be used to disassemble part of it, leaving the ice/water dispenser housing mounted to the refrigerator door. This provides access to the ice/water actuator switch. Perform this disassembly and access to the switch becomes obvious.

The switch is held in place with a single Phillips screw. Make sure that you've disconnected the power to the fridge well before this point because, AFAICT, 120VAC flows through this switch! The switch that I replaced didn't appear to be in bad shape and, once removed, the switch seemed to work correctly when I tested it with an ohmmeter. I replaced it anyway.

Reassembly was straightforward and easy. Better still, ice and water are now dispensed correctly again.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away

Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.