2048778290 Kenmore Upright Vacuum - Instructions

As noted by other users, I tipped the washer on its back to access the water pump underneath. First I had to drain several gallons of water out...I removed the end of the drainage hose from my main basement drain and placed it into a large bin on the floor and it drained itself. Then I removed the two spring clips from the old pump and took off the two hoses. The pump pulled free easily from the drive shaft. I put the new one on, reseated and reclipped the hoses to the pump, and put the washer upright and it worked immediately. Easy repair...saved hundreds on buying new washer.

I did my troubleshooting on line. I took the water pump off, flushed it out, and used a coat hanger to ensure the hoses were not obstructed. Put the water pump back on and reassembled the washer - still would not drain. Checked the lid switch by listening to hear it click, which it did. So, I assumed it was the water pump, so ordered one. Two days later my son-in-law said he experienced the same problem, but it was the lid switch. I decided to check the switch again, this time using my hand to see if it was securely fastened. As soon as I grabed the switch, it sprung apart. I removed it and followed the instructions on how to hot wire the connection for a by pass, and the washer drained. Needless to say I ordered a lid switch assembly. Now I have a new water pump as a backup :) Lesson learned. Opinion: the lid switch assembly is very cheaply made.

I received the water pump. (really quick by the way)
I propped the front of the washer up, removed the old pump and installed the new pump. Ran and test. Piece of cake. I wish I had a better story. Sorry.

It only took using common sense.

It was really simple. All I had to do was take the outside body off of the washer & undo the clamps & take the old water pump off & put the new one on & put the clamps back on & put the body back on. It was easy & a whole lot cheaper than buying a new washer. Thanks for being there.

Got the part in two days! After watching the installation video, i figured i could take the pump off without removing the complete washer panel. Tipped washer on to back and there was the old pump staring at me. Disconnected the two hose clamps with pliers (easy). Hardest part was removing old pump due to crud and rust. Removed pump clamps and forced it off with end of screwdriver alternating both sides. This is why the video shows panel removal. Would have been much easier i think! I used fine sandpaper to get the shaft cleaned up and put a few drops of liquid hand soap into opening of new pump. Lined up the pumped with shaft and it slid right on. Reattached hoses and pump clamps and done!! NO more leak!! Really easy repair - about 15 minutes total.

It was really easy.I tilted washer and removed the clamps holding on the drain hoses and clips holding the water pump and reinstalled the new one.

tilted washer back, changed from underneath

Tipped washer for access to pump. Disconnect hoses. Snap spring clips off of pump. Remove pump from motor shaft. Scotch-Brite shaft, push new pump onto shaft. Reconnect hoses. And your done

After 3 years of hard daily use, the small feet that hold the Bleach dispenser in place broke off. The new dispenser was easy to snap into place and now the washer is good as new.

Removed the two clips holding the pump to the motor, Lift pump off motor and twist pump to allow easy access to hose clamps. Slide clamps off of pump housing, remove hoses and reverse the process just described.

firts i tilt machine over removed water hoses and released water pump lock clips and pulled out. to replaced its reverse process

First I located the leak and removed what was lated identified as the water pump. The pump was secured to a motor by two clamps. Attachted to the water pump were two water hoses. I removed the water pump, took it inside my and started my search for the part on the web. I located your site, followed the site instructions and found the part I needed. For the record, I have never attempted to repair anything in my life. Your site help me save over $300.

I am more than happy to relate this...my 15 month old Whirlpool washer was having a slow leak. Initially, I did not suspect it was the water pump because the appliance was fairly new. When I flipped the washer over, I saw clearly it was comming from the water pump. This pump comes right off after you snap off two clips and loosen two hose clamps. Takes all of 2 minutes! I took the part off and looked for a part number. Then I punched in the part number on my internet and low and behold parts select was one of the links that came up. I just cliqued my way through the order and FEDEXed the part. It came the NEXT BUSINESS DAY! I had it snapped back on and that took another 2 minutes. Don't pay anyone to do this, it's a shame...it's sooooo easy and Partsselect will ship you the part next day. This repair cost me 67 dollars (34 for the part and shipping). Could have easily been 150.00 by a repair man. EASY JOB...NO DOUBT ABOUT IT

This is the same part that is on many Maytag washers. I cannot believe it leaked so soon. I spent 45 minutes or better on the phone with Maytag/Roper. Went through at least 5 people (as I was disconnected once), transfered to someone else mid sentence because I bought it at Lowes. I mean as soon as I said Lowes it was like, beep done. Oh and by the way after all that they still could not find the part I was looking for let alone give me a price. I was looking on the internet while on the phone and found this place. The prints/drawings are awesome and my part came in about 3 days standard shipping. I have book marked this site and will go nowhere else. The repair took about 5 minutes, poped off the old part and on with the new. I only used pliers to disconnect the water so I could move the washer out.

Layed washer on back side
Removed two clips holding pump ,and two clamps on hoses removed pump installed new very,very easy
only needed a pair of pliers.