20231 - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work on getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.

Removed the two screws which held the element in place. Then I pulled the element out about 2-3 inches and disconnected the two wires. Of course I turned off the breaker which fed the range. This had been done earlier so that wife could throughly clean the oven while the element was out of the way, When the new element arrived, we put it into the oven, reconnected the wires to the lugs on the element, pushed it back into the hole, pushed the insulation which protruded back into the hole, and replaced the two screws which held the back plate in place. Turned the breaker back on and turned oven on to test the repair job. Everything worked AOK.

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put slots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

Shut off power, Removed and disconnected element, connected and mounted new element!

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

The part was very easy to locate on the website. The shipping was very fast and the part was easy to install!

1) turned off breaker to oven
2) removed oven racks
3) removed screws holding old element
4) pulled out element far enough to remove 2 wires attached to old element
5) noted colors, left white, right black
6) attached new element to wires
7) attached new element to oven
8) put back oven racks
9) turn breaker back on
10) test oven
done
EASY!!

order process went very well - easy to do

Unscrewed the two screws that held it in place; disconnected the old; connected the new; replaced the screws. DONE.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...removed the baking element and put the new element back in the same way I took the old one out. It was great directions that was posted and easy to do. Best of all I saved the price of a service call. Thank you