1949 - Instructions

First I was amazed that the belt was available for my ancient dishwasher. Then I was amazed again when it came overnight. The instructions said to stretch it over the two pulleys but my hands weren't strong enough. In a sudden flash of brilliance I decided to use a screwdriver as a lever to force it onto the second pulley. Done deal - happy home handyman.

Purchased and installed new faucet attachment. It arrived quickly and very easy to attach. Thank you !

Unscrewed the diswasher from the counter, pulled it out to access the right main door spring and took out the old spring.I installed the plastic washer then slipped the spring throught it and pulled the spring donw with the needle nose vicegrips and inserted the bottom of the spring into the lower hole. I pushed the dishwasher back andrefastened it to the counter.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

Removed two panels on front bottom to gain access to motor and pump pulley.
Looped belt around motor pulley and partially looped belt on larger pump pulley then turned pump pulley together with the belt until belt was fully installed., then coated belt with silicone grease to lubricate it.. very simple procedure.

One note of precaution, UNPLUG power plug before working on appliance.

Since the bimetal repair kit was not available, I bought the complete detergent cup, gasket, and bimetal switch assembly set. This was still far cheaper than paying for a professional repair. All I had to do after shutting off the power is to remove screws to open up the door (door trim/6 screws & 6 screws on the inner side of door edges to remove outer wall of door). The detergent cup assembly is right there for easy access! I unplugged the 2 electric wire plugs to the bimetal switch (paying attention to which plug goes where for when I reassemble), removed the 6 screws that mount the cup assembly, removed assembly and gasket, cleaned the surfaces, and reassembled with the new assembly. Very, very easy to do and everything works like a charm!

Just as everybody explained, 4 screws for the door panel, 6 screws for the dispenser, out and in, 15 minutes!!! There are plenty of screws on the door but, once i knew i was looking for 4 screws, it was a cinch!!! Thanks for that tip. All my appliances are the same age so i 'll be back to this site again!!

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.

No tools were needed. The top rack was slid out as far as it could go (no need to remove from the dishwasher) and the utensil basket was removed. Matching the positioning of the other good clips on the upper rack, the new accessory rack pivot clips were snapped into place. The pins on each end of the accessory racks were placed into the pivot holes provided on the clips and pressed into placed. The bottom prong on each clip was then gently pressed upward until it snapped into the groove on the bottom of the clip. The pivot action of each rack was tested. The untensil basket was put back into place and the upper rack was slid back into the dishwasher. Done!

Clip the plastic on to the vertical pieces. No tools needed

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!