110C68132410 Kenmore Dryer - Instructions

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

Took back panel off, and it was really easy putting the new idler pulley in.

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

C/0 both thermostat sensors and fixed dryer Had no heat out ohmed out the coil and it was ok So I ordered both sensors and replaced them and dryer worked great

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

Had previously replaced the heater coil (purchased from PartSelect) and fixed the no heat problem. Should have taken advice given on this site and replace the thermostat and thermal fuse kit at that time. Since I knew how to remove the assembly it was easier this time. Just remove, unscrew the two parts and replace with the new ones. Reattach the wires and reinstall the assembly and it is now working again. Also vacumed the inside and trimed and replaced the exhast vent hookup for less restriction.

Disconnected the power and duct from the dryer. Removed the back and top of the dryer by removing the 1/4" screws. Created slack in the belt by compressing the spring and moving the idler arm.Slid the belt off the pulley. Removed the tri-ring clip, slid the old pulley and gasket off. Cleaned and inspected the shaft and vacuumed the inside of the dryer. replaced the gasket, pulley and tri-ring clip. Replaced the top and back of the dryer. Connected duct and power.